ABB XSeriesG4 Скачать руководство пользователя страница 92

Страница: 92 / 116

Disconnect the external charging unit J17 from the XRC

board.

Disconnect the battery pack connector, J16, from the board mounted connector.

Disconnect the LCD board cable connector from the XRC

board display interface connector J13.

Remove four XRC

board mounting screws and lock washers. Do not let the screws and lock washer fall onto the board

circuitry.

Move the board away from the door then support it so its circuitry does not come in contact with any metal surface.

Using a 3/16” nut driver, remove the four display board hexagonal mounting standoffs. Lift the board from the door-
mounted standoffs.

NOTE:

If the LCD board is being returned to Totalflow for service, it is recommended that the attached ribbon

cable be left connected and returned with the display board.

To reinstall the display board, perform procedures 4 to 9 in reverse order. Do not over tighten screws. Once the display

board is reinstalled, apply power to the XRC

, adjust contrast potentiometer R32 for optimum display, and verify that the

information displayed on the LCD is correct.

Содержание XSeriesG4





















































































































Результаты поиска

Содержание XSeriesG4

Отзывы:

Бренды по названию

Популярные бренды

ABB XSeriesG4, Руководство пользователя

Результаты поиска

Содержание XSeriesG4

Отзывы:

Бренды по названию

Популярные бренды