ABB XSeriesG4 Скачать руководство пользователя страница 105

Страница: 105 / 116

5 Troubleshooting

XSeriesG4 Remote Controller User's

manual

2103334 Rev. AB

| 93

COLD start procedure (hardware)

NOTE:

Pressing the Reset button with the Memory Backup Enable jumper pulled performs a COLD Start.

If an external charging source is connected, it must be disconnected. Slide the external battery pack charger, CHGR

INPUT +/- terminal block J17 (see Figure 77:

Battery charger and battery pack connections

on page 84), from the

XRC

board green terminal block.

Disconnect the battery pack connector from the XRC

board BAT CONN connector J16 (see Figure 77.)

Disable memory backup, J1 (see Figure 83) by moving the pin jumper to pins 2 and 3.

Figure 83: Lithium Battery Backup Enable/Disable

To return to service, reconnect the 12 Vdc battery pack connector to the XRC

board BAT CONN connector J16 (see

Figure 77), and observe the LCD.

If removed, reconnect the external battery pack charging source to CHGR INPUT connector J17 (see Figure 77.)

Enter all necessary parameters (go to Section 3.5,

Setting up the XRCG4

)or send a saved station file (go to Section 2,

On the

main PCCU screen, on the top menu, select

Operate

File Utilities

Save and Restore Utility

or click the

Save

and Restore Utility

icon on the toolbar.

Click

Save Station Files

at the bottom of the screen. The Save Station files dialog box displays.

In the Save to field, verify or define the location (path) to save the backup file. Take note of the file location for later

retrieval. The default path stores the backup files in the StationFiles directory under the PCCU installation directory. The
backup file default name is the station ID with the .xfc extension.

Click

Wait for the backup to complete. Progress status messages display at the bottom of the screen.

When the upload complete message displays, select

Yes

to restore (copy) the warm configuration to tfCold

Wait for the tfCold update to complete. Progress status messages display at the bottom of the screen.

Verify that the update is complete by expanding tfCold on the navigation tree. Compare the contents of tfCold with tfData

and ensure the configuration files now show in tfCold

When

the XRC

has been COLD-started, the 24-hour clock will reset to 00:00:00.

Enable the memory backup J1 (see Figure 83), by moving the pin jumper to pins 1 and 2.

Содержание XSeriesG4





















































































































Результаты поиска

Содержание XSeriesG4

Отзывы:

Бренды по названию

Популярные бренды

ABB XSeriesG4, Руководство пользователя

Результаты поиска

Содержание XSeriesG4

Отзывы:

Бренды по названию

Популярные бренды