ABB XIO-00 Скачать руководство пользователя страница 30

Страница: 30 / 207

| XIO USER MANUAL | 2106424MNAB

Table 3-2: Ferrule specifications

Cross section

Length

0.25 mm²

5 mm to 7 mm

0.5 mm²

8 mm to 10 mm

0.75 mm²

8 mm to 10 mm

1 mm²

8 mm to 10 mm

1.5 mm²

10 mm

Figure 3-2: COM 1 to COM 8 serial communication port pinouts

Legend: COM 1 to COM 8 serial communication port pinouts

PIN

RS-232

RS-485

RS-422

Voltage out (VOUT)

Ground (GND)

Switched voltage (SW VOUT) Switched voltage (SW VOUT) Switched voltage (SW VOUT)

Ground (GND)

Request to send (RTS)

Transmit/Receive (BUS+)

Transmit Bus + (TBUS+)

Transmit data (TX)

Transmit/Receive (BUS-)

Transmit bus – (TBUS-)

Request to send (RX)

Not Used

Receive bus + (RBUS+)

Clear to send (CTS)

Not Used

Receive bus – (RBUS-)

To wire the serial communication port:

NOTICE – Equipment damage

. Pin 1 (VOUT) or pin 3 (SW VOUT) can power an external device on

all COM ports. The external power supply connected to the power port determines the output voltage

at these pins.
Verify that the device is compatible with the input voltage at the power port before connecting to

these pins. Connection to an incompatible device can result in damage to the device.

Содержание XIO-00
















































































































































































































Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды

ABB XIO-00, Руководство пользователя

Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды