ABB XIO-00 Скачать руководство пользователя страница 26

Страница: 26 / 207

| XIO USER MANUAL | 2106424MNAB

2.3.4

Customer data collection files

The data collection files contain all the trend data the XIO generates. These data files are in the tfData

directory with the running configuration files. The type and amount of collection data depend on the

number and type of trends active on the device.

IMPORTANT NOTE

: The tfData directory also contains the calibration files if the controller has

been field-calibrated.

2.4

User interface

The PCCU32 software running in a Windows

environment is the main user interface to the XIO. PCCU32

supports several view levels and can be configured to provide role-based secure access to the controller

for the following tasks:

–

Initial configuration and commissioning (setup)

–

Monitor the controller operation and performance

–

Add, configure, and optimize applications (configuration)

–

Calibration

–

Data collection

2.5

Secure service access interface

The Secure Shell (SSH) and Secure File Transfer Protocol (SFTP) on the XIO allow secure login access and

file transfer capability for advanced service access. SSH provides an encrypted communication channel,

which requires private key authentication for access to the controller. Secure access is available for

troubleshooting purposes only and is reserved for advanced users and ABB technical support or

development personnel.

Installation

This chapter provides information for XIO installation and setup.

IMPORTANT NOTE

: Read the installation chapter and review user drawings before beginning

installation. Make sure to review safety warnings carefully.

WARNING– Bodily injury

. Although there may be alternate methods of installation and

commissioning of the XIO, ABB recommends that technicians perform the procedures in the order

presented: plan, install, wire, then apply power, verify power-on sequence, and configure.

3.1

Site planning and requirements

XIO installation requires that customer-supplied enclosures, power sources, wiring, and location comply

with the specifications described in this section.

WARNING– Bodily injury

. Carefully review the specifications in this section to select compliant

equipment. Failure to comply with these specifications may create unsafe conditions, resulting in

bodily injury and equipment damage.

3.1.1

Enclosure requirements

Install an XIO standalone on a DIN rail on an interior wall, in an

CORE enclosure, or in a customer-

supplied enclosure.

Содержание XIO-00
















































































































































































































Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды

ABB XIO-00, Руководство пользователя

Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды