ABB XIO-00 Скачать руководство пользователя страница 27

Страница: 27 / 207

XIO USER MANUAL | 2106424MNAB |

For general purpose nonhazardous locations, the XIO must be installed in an enclosure that complies with

the following specifications:

–

For general purpose locations, the enclosure must protect the XIO against shock and impact.

For hazardous locations, the XIO must be installed in an enclosure that complies with the following

specifications:

–

For Class I, Division 2, the enclosure must be rated at least Type 3R, according to the environment.

–

Class I, Zone 2 requires an enclosure that meets IP54 rating and according to IEC 60529 and IEC

60079-0.

Verify that customer-supplied enclosures meet these requirements.

3.1.2

Location requirements

The installation location should:

–

Allow access to the enclosure, XIO, power sources, cables and connections

–

Be at a distance that does not exceed the maximum or recommended field wiring lengths for

connections to peripherals or external equipment. Field wiring requirements depend on the type of

connection. See section

3.1.4.

3.1.3

Mounting requirements

Mounting surfaces or walls require enough strength to support the hanging weight of the enclosure, and

associated equipment to meet the requirements of IEC715.

3.1.4

Install antenna (for wireless functionality)

Wireless support is optional on the XIO. If your device has a wireless interface connector, make sure to

obtain the antenna required to enable communication.

IMPORTANT NOTE:

The Wi-Fi Kit (part number

2106123

) is required for antenna installation.

See

Additional information.

3.2

Wiring requirements

Field wiring must meet the following requirements:

–

All wiring connections and the screw terminals for power support 14 – 24 AWG and communications

support 16 - 24 AWG. Select the wire gauge according to the voltage and current requirements of the

circuitry. The gauge differs for each application.

–

Follow local electrical codes to select the appropriate wire gauge and type based on the load current,

voltage, signal type, and indoor or outdoor environment.

NOTICE – Equipment damage

. Field installation cable and conductors must be rated greater than

70 °C (158 °F) when installed in an ambient temperature of 60 °C (140 °F).

3.3

Unpack and inspect

The XIO and additional parts ship in a specially designed shipping carton with a Quick Start Guide, Safety

and Compliance notice, and packing list.

IMPORTANT NOTE

: If there is any damage to the shipping carton, keep it and the packing

materials until the contents are inspected and found to be free of damage.

Содержание XIO-00
















































































































































































































Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды

ABB XIO-00, Руководство пользователя

Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды