ABB XIO-00 Скачать руководство пользователя страница 127

Страница: 127 / 207

XIO USER MANUAL | 2106424MNAB |

127

IMPORTANT NOTE:

Record the security codes. They are not visible on the Station Setup tab after you

save them.

Enforcement of the security codes is in effect.

IMPORTANT NOTE:

PCCU32 requires the security codes the next time it attempts to connect to the

device. The security codes in PCCU32 version 7.68 or later do not prevent MODBUS

access to the XIO.

7.5.1

Configure non-default XIO security code on the RMC

The XIO Interface application requires read and write privileges to work properly with the XIO. If the XIO

security level 2 code (write protection) is non-default, you must configure this code in the XIO Interface

Communications Setup (in the XIO Security Code field). The position of the security switch does not

remove the requirement for the XIO Interface App to be configured for level 2 access.

This procedure configures the XIO level 2 security code in the XIO Interface to allow the RMC to perform

writes on the XIO. Connection failure occurs when the incorrect security code is configured in the XIO

Interface.
This procedure assumes that the XIO level 2 security code has already been configured on the XIO

Station Setup

tab, and that the code was recorded for safe keeping. Once configured, the security code

is not visible on the screen. Before proceeding, obtain the correct code.
To configure the security code on the RMC:

Содержание XIO-00
















































































































































































































Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды

ABB XIO-00, Руководство пользователя

Результаты поиска

Содержание XIO-00

Отзывы:

Бренды по названию

Популярные бренды