ABB TRS 61D01 страница 109 Скачать руководство пользователя

Страница: 109 / 114

Operation Manual / TPS48-D/E.. - TPS61-D/E..

12 Spare parts / 12.1 Ordering spare parts

HZTL2410_EN

Rev.F

March 2020

12 Spare parts

12.1 Ordering spare parts

When making inquiries or ordering spare parts, the following data must
be specified:

Turbocharger type

Serial number (HT……)

Designation and part number.

Spare parts can be ordered from an official ABB Turbocharging service
station.

If different design versions have not been taken into consideration in
this document, please contact an ABB Turbocharging service station.

CAUTION

Storage of spare parts

All spare parts ordered with the turbocharger must be kept complete
and ready for use.

Parts showing signs of rust should be carefully cleaned and greased.

Dispose of replaced and unusable parts in a professional and environ-
mentally compatible way.

Customer spare part set (97070)

The customer spare part set (97070) is required for the work described
in this Operation Manual.

Quantity

Description

Part number

Socket screw

42008

O-ring

81010/ 82010

O-ring

77005

O-ring

42012

Gasket

52406 *

* This gasket can only be installed when a gas outlet casing from ABB is
used.

Page

107

111

All manuals and user guides at all-guides.com

Содержание TRS 61D01



















































































































Результаты поиска

Содержание TRS 61D01

Отзывы:

Похожие инструкции для TRS 61D01

Бренды по названию

Популярные бренды

ABB TRS 61D01, Руководство по эксплуатации

Результаты поиска

Содержание TRS 61D01

Отзывы:

Похожие инструкции для TRS 61D01

Бренды по названию

Популярные бренды