ABB TRS 61D01 страница 3 Скачать руководство пользователя

Страница: 3 / 114

Operation Manual / TPS48-D/E.. - TPS61-D/E..

Table of contents

HZTL2410_EN

Rev.F

March 2020

Operation Manual

Preliminary remarks................................................................................................. 3

1.1

Purpose of this manual .................................................................................................. 3

1.2

Layout and function........................................................................................................ 4

1.3

Intended use of the turbocharger .............................................................................. 6

1.4

Storage of new turbochargers and spare parts ....................................................... 7

1.5

Essential information..................................................................................................... 9

1.6

Symbols and definitions .............................................................................................. 11

1.7

Turbocharger rating plate ........................................................................................... 12

1.8

Contact information..................................................................................................... 13

Safety...................................................................................................................... 14

2.1

Introduction ................................................................................................................... 14

2.2

CE conformity ................................................................................................................ 14

2.3

Definition of mandatory signs ................................................................................... 15

2.4

Definition of Safety instructions ............................................................................... 15

2.5

Warning plates on the turbocharger......................................................................... 16

2.6

Safe operation and maintenance............................................................................... 17

2.7

Hazards during operation and maintenance........................................................... 20

2.8

Deflagration on gas engines....................................................................................... 25

2.9

Periodic checking of the pressure vessel ................................................................. 26

2.10

Lifting loads ................................................................................................................... 26

Commissioning...................................................................................................... 28

3.1

Oil supply ........................................................................................................................ 28

3.2

Inspection work ............................................................................................................. 32

3.3

Commissioning after taking out of operation........................................................ 34

Operation ............................................................................................................... 35

4.1

Noise emissions ............................................................................................................ 35

4.2

Servicing work ............................................................................................................... 37

4.3

Expected exchange intervals ..................................................................................... 40

4.4

Speed measurement .................................................................................................... 42

4.5

Stopping the engine .................................................................................................... 45

Maintenance .......................................................................................................... 46

5.1

Foreword to Maintenance .......................................................................................... 46

5.2

Cleaning the compressor during operation ............................................................ 47

5.3

Turbine cleaning during operation............................................................................ 51

5.4

Cleaning components mechanically.......................................................................... 58

All manuals and user guides at all-guides.com

Содержание TRS 61D01



















































































































Результаты поиска

Содержание TRS 61D01

Отзывы:

Похожие инструкции для TRS 61D01

Бренды по названию

Популярные бренды

ABB TRS 61D01, Руководство по эксплуатации

Результаты поиска

Содержание TRS 61D01

Отзывы:

Похожие инструкции для TRS 61D01

Бренды по названию

Популярные бренды