ABB TRS 61D01 страница 26 Скачать руководство пользователя

Страница: 26 / 114

Operation Manual / TPS48-D/E.. - TPS61-D/E..

2 Safety / 2.7 Hazards during operation and maintenance

HZTL2410_EN

Rev.F

March 2020

Hazards when handling insulating materials

WARNING

Hazards due to insulating materials

Dust and fibres from insulating materials can cause damage to health
or irritations. Unsuitable, combustible insulating materials signify a fire
hazard.

Use only suitable, non-combustible insulating materials.

Ensure that the work area is well ventilated.

Avoid stirring up dust.

Use tools and processes which keep dust to a minimum.

Remove packing materials only in the work area.

Take particular care when removing old insulating materials.

Dispose of insulating materials properly and in an environmentally
compatible way in accordance with applicable local regulations.

Wear safety goggles.

Wear a respiratory mask to protect against dusts.

Wear safety gloves to protect against chemical hazards.

Use only suitable, non-combustible insulating materials.

Ensure that the work area is well ventilated.

Wear suitable work clothing (safety glasses, respiratory mask).

Avoid stirring up dust.

Use tools and processes which keep dust to a minimum.

Remove packing materials only in the work area.

Take particular care when removing old insulating materials.

Dispose of insulating materials properly and in an environmentally
compatible way in accordance with applicable local regulations.

Page

111

All manuals and user guides at all-guides.com

Содержание TRS 61D01



















































































































Результаты поиска

Содержание TRS 61D01

Отзывы:

Похожие инструкции для TRS 61D01

Бренды по названию

Популярные бренды

ABB TRS 61D01, Руководство по эксплуатации

Результаты поиска

Содержание TRS 61D01

Отзывы:

Похожие инструкции для TRS 61D01

Бренды по названию

Популярные бренды