ABB TRS 61D01 страница 19 Скачать руководство пользователя

Страница: 19 / 114

Operation Manual / TPS48-D/E.. - TPS61-D/E..

2 Safety / 2.6 Safe operation and maintenance

HZTL2410_EN

Rev.F

March 2020

2.6 Safe operation and maintenance

The instructions specified in this section are for the safety of personnel.
Together with the instructions in the Hazards during operation and
maintenance section, they allow the user to safely use the turbocharger.

Work safety and work area safety

WARNING

Risk of falling

There is the risk that someone can fall when working on the turbochar-
ger.

Do not climb on the turbocharger or on parts attached to it or use
these as climbing aids.

When working at levels above the head, use climbing aids and work
platforms suitable for this purpose.

Observe all general regulations for the prevention of accidents.

Do not work on the turbocharger if you are under physical or mental
stress.

Work only with suitable tools as well as equipment and working ma-
terials that are in perfect condition.

Electric tools must be solidly earthed, and connecting cables may not
be damaged.

Keep the workplace clean, clear away loose objects and remove
obstacles on the floor.

Keep the floor, equipment and the turbocharger clean.

Have oil binding materials ready at hand and keep oil catch pans
ready or in position

Eliminate leaks.

Keep fire-protection materials and fire-extinguishing equipment
ready.

Welding work in the vicinity of the turbocharger

When performing welding work in the vicinity of the turbocharger, al-
ways cover the filter silencer to prevent the filter mat from being
damaged.

Keep flammable objects and substances out of the range of flying
sparks.

Cover all connections on the turbocharger so that no foreign objects
can enter the turbocharger.

Wear personal protective equipment (PPE) for welding operations.

Page

111

All manuals and user guides at all-guides.com

Содержание TRS 61D01



















































































































Результаты поиска

Содержание TRS 61D01

Отзывы:

Похожие инструкции для TRS 61D01

Бренды по названию

Популярные бренды

ABB TRS 61D01, Руководство по эксплуатации

Результаты поиска

Содержание TRS 61D01

Отзывы:

Похожие инструкции для TRS 61D01

Бренды по названию

Популярные бренды