ABB Triguard SC300E Скачать руководство пользователя страница 5

Страница: 5 / 65

Document Reference SS 0728
Issue 5 - September 2006

Appendix 2 - Time Constraint Table (Low Demand of operation)................................ 53

9.1

Admissible Repair Times in hours for Low Demand Mode of Operation .................................... 53

Appendix 3 - Approved RTTS Versions ......................................................................... 54

Appendix 4 - RTTS versions 8.30-005 and later versions............................................. 55

11.1

System Error Flags for RTTS version 8.30-005 and later versions............................................. 55

11.2

MHB44IND 4 channels pulse input and 4 channel analogue output module.............................. 56

11.3

MAO04IND 4 channel analogue output module.......................................................................... 56

11.4

System identification..................................................................................................................... 56

11.4.1

SC300E RTTS 8.30-005...................................................................................................... 56

11.4.2

SC300E RTTS 8.30-006...................................................................................................... 56

Appendix 5 – RTTS 8.30-007 and 008............................................................................. 57

12.1

System Identification RTTS 8.30-007 .......................................................................................... 57

12.2

Change History............................................................................................................................. 57

12.3

System Identification RTTS 8.30-008 .......................................................................................... 57

12.4

Change History............................................................................................................................. 57

Appendix 6 - TUV Approved Part Numbers and Revisions.......................................... 59

13.1

Hardware Approvals..................................................................................................................... 59

13.2

Software Approvals. ..................................................................................................................... 63

Table of Figures

Figure 1 System Overview .................................................................................................................... 10

Figure 2 Current to Voltage Conversion ................................................................................................ 14

Figure 3 Dual Final Elements ................................................................................................................ 17

Figure 4 Dual outputs to single final element ........................................................................................ 18

Table of Tables

Table 1 FALT Error Flags (RTTS 8.30 versions 001 – 003).................................................................. 21

Table 2 Monitor Flag Register ............................................................................................................... 23

Table 3 Digital Output Fault Flags ......................................................................................................... 23

Table 4 Piano and Analogue Fault Flags .............................................................................................. 24

Table 5 System Alarms.......................................................................................................................... 24

Table 6 FALT flags RTTS 8.30-005 and later ....................................................................................... 55

Содержание Triguard SC300E


































































Результаты поиска

Содержание Triguard SC300E

Отзывы:

Бренды по названию

Популярные бренды

ABB Triguard SC300E, Руководство по безопасности

Результаты поиска

Содержание Triguard SC300E

Отзывы:

Бренды по названию

Популярные бренды