manualshive.com logo in svg

ABB Triguard SC300E, Руководство по безопасности

Поделиться
Скачать
ABB Triguard SC300E Скачать руководство пользователя страница 32

Issue 5 - September 2006

 

Page 32 of 65 

5.4.2 Maintenance 

Actions 

Any maintenance actions specified to be carried out by Operations (eg lamp test) must be 
carried out as specified and results logged. 

5.4.3  Process Trips and Events 

If during the course of normal operation a process trip or event that causes action by the safety 
systems should occur, then all results must be logged and confirmation that the correct safety 
action demanded occurred should be made. 
 
Before restarting the process after an event, the plant safety supervisor must confirm that the 
plant is safe to be re-started. 

5.4.4 Maintenance 

Engineering 

Station 

The TriBuild Maintenance Engineering Station should not be connected to the system during 
normal operation. 

5.5 System 

Shutdown 

The Safety System would normally only be shutdown during a planned major plant maintenance 
cycle.  During this period it is likely that both major equipment will be dismantled and serviced, 
and possible process and system parameters modified. 
 
If process and system parameters are to be modified, then Section 7, Maintenance and 
Modification must be adhered to. 

5.5.1 Process 

Shutdown 

Before the Triguard SC300E Safety System is shutdown the process must first be safely shut 
down and the plant brought to a safe/neutral state. 
 
This would normally require that all hazardous materials are removed and the process purged. 

5.5.2  Triguard SC300E System Shutdown 

The Triguard SC300E System Shutdown will be documented in the supplied bespoke 
Operations and Maintenance Manual specific to the plant. 
 
In principle, the following sequence of power down is followed: - 
 

1)  Remove power to main chassis. 

 

2)  Remove power to slave chassis. 

 

3)  Remove power to all fail-safe outputs, final elements and field sensors. 

 

4)  Turn off main panel power breakers.   

Содержание Triguard SC300E


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды