manualshive.com logo in svg

ABB Triguard SC300E, Руководство по безопасности

Поделиться
Скачать
ABB Triguard SC300E Скачать руководство пользователя страница 16

Issue 5 - September 2006

 

Page 16 of 65 

3.3.2.6 Hot 

Repair 

Adapters 

Wherever dual slot hot repair facilities are required, the hot repair adapter boards must be fitted 
on the chassis backplane. 

3.4  Classification (SIL level) System Time Constraint 

The Triguard SC300E Safety PLC is a fault tolerant system that inherently tolerates and reports 
a first major fault (for example a processor failure). 
 
The system diagnostics of a digital output module are not fully available after a first fault is found 
on the module.  The time allowed to repair this module before a shutdown to the safe state is 
required is the system time constraint. 
 
The Triguard SC300E System may be configured with or without time constraint dependent on 
the safety output configurations used. 
In systems configured with single outputs and final elements, then a time constraint will apply.  
 
The time constraint has been conservatively calculated by TUV dependent on the SIL level (low 
demand) and based on worst case of all outputs used. 
 

Time constraint for SIL 3 systems is 2353 hours 

 

Time constraint for SIL 2 systems is 7440 hours 

 

Time constraint for SIL 1 systems is 23528 hours 

 
Time constraint may be extended if less than 32 outputs are safety related, for extended time 
constraint values refer to the table Appendix 2. 

3.4.1  Without System Time Constraint Dual Final Elements 

In AK6 (SIL 3) classified safety loops it is probable that the safety loop final element has at least 
two possible operational paths (Figure 3 shows a typical configuration). 
 
Providing each final element is driven from a separate SC300E digital output on separate digital 
output modules, the system will have no time constraint. 
 

Dual
Solenoid
Valve

Dual Solenoid Example

MDO Card 1

TC

MDO Card 2

TC

SC300E TMR
System

MDO Card 1

TC

ESD Valve 1

MDO Card 2

TC

ESD Valve 2

SC300E TMR
System

Dual Valve Example

Содержание Triguard SC300E


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды