ABB RELION 650 SERIES Скачать руководство пользователя страница 59

Страница: 59 / 110

Section 6

Local HMI engineering

6.1

LED and function key engineering

GUID-18B1952A-7578-4AC5-8A62-88FE60067292 v3

6.1.1

Local HMI engineering process

GUID-35126910-CF1C-4411-ACA9-72E1DB9BC68F v5

The engineering process of the LEDLHMI involves several steps.

Figure 42

presents the pre-

engineering step, the main steps in the engineering process and the required sequences.

IEC09000622_1_en.vsd

Local HMI

ACT / SMT

Select and configure

HMI function blocks

PST

Set function

keys and LEDs

END

SAVE

GDE / ACT

Create the

single line diagram

SAVE

IEC09000622 V1 EN-US

Figure 42: LHMI: Engineering process flowchart

•

Application Configuration tool with possible assistance of Signal Matrix tool
•

To use the function keys and LEDs on LHMI it is needed to insert the corresponding

special function blocks for these operation element groups.

•

The function blocks for the LEDs are organized as single function block per LED but

indexed to the group identification, for example GRP1_LED3 (indication LED 3 in

virtual LED group 1).

•

The function blocks for LHMI are visible by default for Parameter Setting tool.

•

Use Application Configuration tool to connect start and trip signals from application

functions to LED function blocks.

•

Parameter Setting tool
•

The operation mode of the function keys and the LEDs is defined in Parameter

Setting tool.

•

The presented text labels on the LCD for LHMI keys and LEDs.

•

Graphical Display Editor with assistance of Application Configuration tool, for example

1MRK 511 284-UEN B

Section 6

Local HMI engineering

650 series

Engineering manual

Содержание RELION 650 SERIES














































































































Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

ABB RELION 650 SERIES, Инструкция по эксплуатации, Страница: 59 / 110

Результаты поиска

Содержание RELION 650 SERIES

Отзывы: