ABB RELION 650 SERIES Скачать руководство пользователя страница 40

Страница: 40 / 110

IEC09000664_3_en.vsd

IEC09000664 V3 EN-US

Figure 23: PCM600: IED Setup completion wizard

It is not possible to go back and do any modifications in the setup complete

page. If an error is detected, the insertion has to be canceled and the IED has to

be inserted again.

When the online configuration is completed, it is advised to read the

configuration from the IED to ensure that the IED object in PCM600 has the

same configuration data as the physical IED.

Inserting an IED in offline mode

Working in offline mode has an advantage compared to online mode that one can start

preparing configuration even though IED is not available. Setting up an IED in offline mode is

almost similar to that of an online mode; however with offline mode it is not necessary to type

the correct IP address in the Communication port and IP address dialog.

The version information and order specific file needs to be selected, see

Figure 24

. The order

specific file is delivered in a order confirmation E-mail. If no order specific file is available then

select the

No Order Specific File option, see

Figure 25

Section 4

1MRK 511 284-UEN B

Setting up a project

650 series

Engineering manual

Содержание RELION 650 SERIES














































































































Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

ABB RELION 650 SERIES, Инструкция по эксплуатации, Страница: 40 / 110

Результаты поиска

Содержание RELION 650 SERIES

Отзывы: