ABB RELION 650 SERIES Скачать руководство пользователя страница 12

Страница: 12 / 110

The information icon alerts the reader of important facts and conditions.

The tip icon indicates advice on, for example, how to design your project or

how to use a certain function.

Although warning hazards are related to personal injury, it is necessary to understand that

under certain operational conditions, operation of damaged equipment may result in

degraded process performance leading to personal injury or death. It is important that the

user fully complies with all warning and cautionary notices.

Operation of damaged equipment could, under certain operational conditions, result in

degraded process performance leading to information or property loss. Therefore, comply

fully with all notices.

1.4.2

Document conventions

GUID-96DFAB1A-98FE-4B26-8E90-F7CEB14B1AB6 v2

•

Abbreviations and acronyms in this manual are spelled out in the glossary. The glossary

also contains definitions of important terms.

•

Push button navigation in the LHMI menu structure is presented by using the push button

icons.
For example, to navigate between the options, use

and

•

HMI menu paths are presented in bold.

For example, select Main menu/Settings.

•

LHMI messages are shown in Courier font.
For example, to save the changes in non-volatile memory, select Yes and press

•

Parameter names are shown in italics.

For example, the function can be enabled and disabled with the

Operation setting.

•

Each function block symbol shows the available input/output signal.
•

the character ^ in front of an input/output signal name indicates that the signal

name may be customized using the PCM600 software.

•

the character * after an input/output signal name indicates that the signal must be

connected to another function block in the application configuration to achieve a

valid application configuration.

1.4.3

Functions included in 650 series IEDs

GUID-7FEF6D7A-C3C7-4598-BB0A-0F95624D7C65 v7

Table 1:

Main protection functions

IEC 61850 or Function

name

ANSI

Function description

Differential protection

T2WPDIF

87T

Transformer differential protection, two winding

T3WPDIF

87T

Transformer differential protection, three winding

GENPDIF

87G

Generator differential protection

REFPDIF

87N

Restricted earth fault protection, low impedance

HZPDIF

1Ph High impedance differential protection

Impedance protection

ZQMPDIS

Five-zone distance protection, Quadrilateral and Mho characteristic

Table continues on next page

Section 1

1MRK 511 284-UEN B

Introduction

650 series

Engineering manual

Содержание RELION 650 SERIES














































































































Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

ABB RELION 650 SERIES, Инструкция по эксплуатации, Страница: 12 / 110

Результаты поиска

Содержание RELION 650 SERIES

Отзывы: