ABB Relion 615 series страница 32 Скачать руководство пользователя

Страница: 32 / 136

Table 11:

Alarm indications

LED state

Description

Off

Normal operation. All activation signals are off.

•

Non-latched mode: activation signal is still on.

•

Latched mode: activation signal is still on, or it is off but has not

been acknowledged.

•

Latched flashing mode: activation signal is still on but has been

acknowledged.

Flashing

•

Non-latched flashing mode: activation signal is still on.

•

Latched flashing mode: activation signal is still on, or it is off but has

not been acknowledged.

3.2.4.2

Parameter management

The LHMI is used to access the IED parameters. Three types of parameters can be
read and written.

•

Numerical values

•

String values

•

Enumerated values

Numerical values are presented either in integer or in decimal format with
minimum and maximum values. Character strings can be edited character by
character. Enumerated values have a predefined set of selectable values.

3.2.4.3

Front communication

The RJ-45 port in the LHMI enables front communication. Two LEDs are located
above the communication port.

•

The green uplink LED on the left is lit when the cable is successfully
connected to the port.

•

The yellow communication LED on the right flashes when the IED
communicates with the connected device.

Section 3

1MRS756708 C

615 series overview

615 series

Operation Manual

Содержание Relion 615 series








































































































































Результаты поиска

Содержание Relion 615 series

Отзывы:

Похожие инструкции для Relion 615 series

Бренды по названию

Популярные бренды

ABB Relion 615 series, Руководство по эксплуатации

Результаты поиска

Содержание Relion 615 series

Отзывы:

Похожие инструкции для Relion 615 series

Бренды по названию

Популярные бренды