manualshive.com logo in svg

ABB +Q951, Руководство пользователя, Страница: 42 / 56

Поделиться
Скачать
ABB +Q951 Скачать руководство пользователя страница 42

Resetting the safety function

WARNING!

Make sure that the drive does not start accidentally. This can occur after the reset
of the safety function, if a level-triggered start command and the start enable signal
are on at the same time.

1. Return the emergency stop button [S61] or user-defined push button to the normal

position. For example, turn the emergency stop button [S61] until it releases.

2. Push the emergency stop reset button [S62] on the cabinet door for 0.1 … 3 seconds.

The emergency stop reset button indicator light [S62] goes off, and the emergency stop
is deactivated.

3. If necessary, reset faults from the drive.

4. If necessary, close the main contactor/breaker.

5. Make sure that the drive receives the start signal.

6. You can now restart the drive.

For more information, see the hardware and firmware manuals.

Note:

You must also reset the emergency stop safety relay [A61] or [A640] with the

emergency stop reset button [S62] each time after you energize the relay. If you do not
reset the relay, you cannot close the main contactor/breaker.

42 Use of the safety function

Содержание +Q951

























































Отзывы:

Нет отзывов