ABB PVS-60-TL-R-US Скачать руководство пользователя страница 42

Страница: 42 / 174

- 42 -

001046AG

3 - Characteristics

Configurable relays

The inverter is equipped with two configurable switching relays, which

can be used in different operating configurations that can be set using

the web user interface. A typical example of application is closing the

contact when an alarm is triggered.

Remote switch-on/switch-off

This command can be used to switch off/switch on the inverter via an

external (remote) command using the Remote ON/OFF terminal block.

This functionality must be enabled in the web user interface and when

active, switching on the inverter, besides being dictated by the presence

of normal parameters which allow the inverter to be connected to the grid,

also depends on the external control for switching on/off.

Reactive power feed into the grid

The inverter is able to produce reactive power and can feed this power

into the grid via the power factor setting.

Power feeding modes vary according to the country or state/province of

installation and the grid companies.

Limiting the active power fed into the grid

The inverter can limit the amount of active power fed into the grid by the

inverter to the desired and adjustable value.

Overvoltage surge arrester monitoring

The inverter monitors the status of the overvoltage surge arresters, and

generates a warning in the event of a fault (viewable via monitoring sy-

stem, internal web user interface or Installer Mobile APP).

RSD board (only -R models) *

Rapid shut down (RSD) board allows fast discharge of positive and ne-

gative input voltages to ground: when used in conjunction with a device

able to discharge differential input voltage, the whole system is compliant

with NEC 2017 690.12 RSD requirements. Since RSD is a safety-related

feature, RSD board self-test is repeated every 24 hours during inverter

initialization phase: self-test fails if RSD functionality is damaged, resul-

ting in alarm E103.
* Must be installed and operated in conjunction with external panel level

rapid shut down devices (please refer to local sales representative for a

list of compatible devices).

Data transmission and control

Embedded multi communication interfaces (WLAN, Ethernet, RS485)

combined with a Sunspec compliant Modbus protocol (RTU/TCP) allow

the inverter to be easily integrated with any third party monitoring and-

control systems that support the same Sunspec standard.

Please contact the ABB technical support or get access to Sunspec alliance website for further

information on Modbus Sunspec products.

Содержание PVS-60-TL-R-US















































































































































































Результаты поиска

Содержание PVS-60-TL-R-US

Отзывы:

Бренды по названию

Популярные бренды

ABB PVS-60-TL-R-US, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-60-TL-R-US

Отзывы:

Бренды по названию

Популярные бренды