manualshive.com logo in svg

ABB PVS-60-TL-R-US, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB PVS-60-TL-R-US Скачать руководство пользователя страница 158

- 158 -

001058AG

8 - Maintenance

- Error code

- Error message 

- Warning

Name of Alarm and Cause

Solution

- E033

- UTH

-   

Yellow LED

Low ambient temperature:

Temperature outside the inverter below -25°C

• Wait for the temperatures to which the inverter is exposed to 

return to the operating range.

- If the problem persists, contact customer assistance. You 

must remember to wait for the time necessary to allow the 

inverter to warm up.

- E034 

- Interlock fail

-   

Yellow LED

“IGBT” circuitry not ready:

Error inside the inverter

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

- E035*

- Remote Off

-   

Yellow LED

Inverter awaiting “remote ON” command:

The inverter has been switched off remotely (remote 

OFF) and remains in waiting state for the signal that 

will switch it on again (remote ON).

• Switch the inverter back on remotely. If the unit does not 

switch on, disable the remote on/off function and switch the 

equipment off completely and then switch it on again.

- If the problem persists (once the Remote ON/OFF function 

has been reactivated), contact customer assistance.

- E036

- Vout Avg error

-   

Yellow LED

Average of the measurements of grid voltage 

outside of range:

The average value of the grid voltage (sampled every 

10 minutes) does not fall within the permitted ranges. 

The grid voltage in the point connected to the inverter is 

too high. This may be caused by a grid impedance that 

is too high. In the final stage of the timeout, the inverter 

limits the power to check whether the grid voltage 

has stabilised into regular parameters. If this does not 

happen, the inverter disconnects from the grid 

• Check the grid voltage in the connection point to the inverter.

- If the grid voltage differs from the range due to the conditions 

of the distribution grid, ask the operator to adjust the grid 

voltage. If the operator authorises a change to the inverter's 

parameters, agree the new limits with customer assistance.

- E037

- Riso Low

-   

Red LED

Low value of the isolation resistance (only with 

the “Amorphous” mode activated):

This error can appear only if the “Amorphous” mode 

is enabled. This function is enabled only in inverters 

equipped with grounding kit and is used to monitor 

the voltage at the ends of the grounding resistor. The 

error appears when the voltage at the ends of the 

resistor connected between ground and pole of the 

photovoltaic generator exceeds 30V for more than 30 

minutes or 120V for more than one second.

• Check for the presence and correct contact between the 

two terminals of the grounding resistance installed inside the 

inverter

• Measure the isolation resistance using a megohmmeter 

positioned in the photovoltaic array (positive terminal short-

circuited at the negative pole) compared to ground. The 

measurement is strongly influenced by the environmental 

conditions, so must be made under the same conditions in 

which the error occurred.

- If the value measured is lower than 1 megaohm, a 

check must be carried out by a technician/installer on the 

photovoltaic generator to identify and eliminate the problem.

- If the value measured is higher than 1 megaohm and the 

error signal persists, contact customer assistance.

 E046

- String self test fail

- 

 No LED

Error during the automatic check of the string 

voltages (only in models with the “fuse-control” 

board):

In some inverter models it is possible to carry out the 

check test of the polarity of the strings connected to 

the input (e.g.:TRIO-20.0/27.6kW).

This error signal occurs when, during the test stage, 

an inverted string is recorded 

• Section the inverter and check the polarity of the string(s) 

which the inverter has recorded as inverted.

- Once all the strings have been correctly connected, activate 

the system once again; the inverter will once again check the 

correct polarity of the string inputs at the end of which it will 

carry out the checks for the grid connection.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

 E049

- AC FF Error

-   

Yellow LED

Error in the “AC feed-forward” circuit:

Error inside the inverter

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

 E050

- AFDD Activated

-   

Yellow LED

Arc Fault protection activated:

Possible photovoltaic arc detected on the DC side.

• If it is the first time this problem has occurred, press the ESC 

button for 5 seconds and wait for the unit to restart.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

 E051

- Safety mem. Fault

-   

Yellow LED

Error inside the inverter.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

 E053

- AFDD Fault

-   

Yellow LED

Arc Fault board autotest failed:

Problem detected during the AFDD board autotest 

phase.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

 E054

- AFDD comm. Fault

-   

Yellow LED

Arc Fault board communication error:

Error on the RS485 serial communication detected 

between the inverter and the AFDD board.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

 E055

- AFDD wrong conf.

-   

Yellow LED

Arc Fault board parameter reading error:

Error in the parameter reading by the system.

• Error inside the inverter and cannot be checked externally.

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

Содержание PVS-60-TL-R-US















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды