ABB PVS-60-TL-R-US Скачать руководство пользователя страница 133

Страница: 133 / 174

- 133 -

000877BG

7 - Operation

Firmware Update

By accessing to the

Firmware Update

sub-menu you can upgrade the

firmware of the inverter and his components selecting a Remote firm-

ware Update or a Local firmware Update.

Perform the update during good irradiation conditions (avoid the dawn and dusk hours).

An interruption of updating process could damage the inverter!

• Remote firmware Update:

In remote mode, the firmware will update automat-

ically, searching the last available firmware on ABB

servers, by clicking the “CHECK” button.

After the finish of the checking process the avail-

able release will be notified on the bottom part of

the section

Click on “UPDATE” button to start with the updating

process.

• Local firmware Update:

By updating in local mode, the firmware have to be selected and up-

loaded from local folder of the used devices to access to the web server.
The latest firmware version is available from the download area of the

website

www.abb.com/solarinverters

or from

https://registration.

abbsolarinverters.com

Click on “FW SELECT” and select the firmware

package previously downloaded.

Click on “UPDATE” button to start with the updating

process.

Содержание PVS-60-TL-R-US















































































































































































Результаты поиска

Содержание PVS-60-TL-R-US

Отзывы:

Бренды по названию

Популярные бренды

ABB PVS-60-TL-R-US, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-60-TL-R-US

Отзывы:

Бренды по названию

Популярные бренды