manualshive.com logo in svg

ABB PVS-60-TL-R-US, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB PVS-60-TL-R-US Скачать руководство пользователя страница 159

- 159 -

001058AG

8 - Maintenance

- Error code

- Error message 

- Warning

Name of Alarm and Cause

Solution

 E056

- Over Temp. (from 

external box)

-   

Yellow LED

Excessive temperature measured inside the 

inverter's wiring box:

High internal temperature. 

This error relates to the temperature measured on 

external boxes (e.g.:TRIO-20.0/27.6kW).

• Check that the inverter is not exposed to direct sunlight. Wait 

for the temperatures to which the inverter is exposed to return 

to the operating range and for the inverter to cool down.

- If the problem persists (once the ambient temperature has 

returned to within the range), contact customer assistance. 

Remember to wait the time needed to allow the inverter to 

cool down

 E057

- Vbulk reading error

-   

Yellow LED

Input voltage (Vin) higher than booster voltage 

(Vbulk):

The error occurs if the input voltage exceeds the 

Bulk voltage (voltage on the DC-DC circuit inside the 

inverter)

• It is necessary to measure the input voltage inside the 

inverter with a voltmeter.

- If it is higher than the maximum voltage of the operating 

range, the alarm is genuine and it is necessary to check the 

configuration of the PV generator. If the voltage has also 

exceeded the maximum input threshold the inverter could be 

damaged. 

- If it is lower than the maximum voltage of the operating 

range, the alarm is caused by an internal malfunction and it is 

necessary to contact customer assistance.

 E058

- Pin vs Pout check 

error

-   

Yellow LED

Error in the check of Pin vs Pout:

The error occurs if the difference between the 

measured value of input power and that of output 

power is greater than the limit imposed internally to 

the inverter. 

• Error inside the inverter and cannot be checked externally. 

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

 E074

- Internal error

-   

Yellow LED

Communication error inside the inverter:

The alarm occurs when there are communication 

problems between the control devices inside the 

inverter.

• Error inside the inverter and cannot be checked externally. 

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

 E077

- Internal Error

-   

Yellow LED

Error in the system configuration:

Error inside the inverter

• Error inside the inverter and cannot be checked externally. 

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

 E078

- Riso Test fail

-   

Yellow LED

Riso test error:

Problem detected during the Riso test phase.

• Error inside the inverter and cannot be checked externally. 

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

 E079

- Wrong Sequence

-   

Yellow LED

Incorrect Phases connection

(Only triphase models) The phases have not been 

connected correctly to the AC output

• Invert two of the phases of the network wiring to the AC 

terminal block of the inverter.

 E081

- Internal Error

-   

Red LED

Inverter fault / Incomplete inverter closing:

Fault inside the inverter or incomplete inverter closing 

(front cover missing or not tightened, cable glands 

missing or incorrectly tightened, environmental 

protection IP65 not guaranteed)

• If the problem has occurred during the installation phase or 

during the inverter maintenance phase (therefore the cover 

has been removed or the cable glands have been acted 

upon), carry out the following operations:

- Disconnect the AC grid and DC input from the inverter 

and check for the front cover and all the cable glands, also 

checking their correct tightening to ensure environmental 

protection IP65; reconnect the AC grid and the DC input and 

attempt to switch the inverter on; if the problem persists, 

contact customer assistance :

- If the front cover and all cable glands are present, disconnect 

the AC grid and DC input from the inverter and wait 15 

minutes at a safe distance, then open the inverter cover and if 

no smoke/smell of burning is present, check the integrity of the 

components or the presence of moisture or other abnormal 

conditions; reconnect the AC grid and DC input and attempt to 

switch on the inverter; if the problem persists contact customer 

assistance.

• If the problem has occurred after installation or after an 

inverter maintenance phase (therefore the cover has NOT 

been removed or the cable glands have NOT been acted 

upon), disconnect the AC grid and the DC input from the 

inverter and contact customer assistance.

 E084

- BackFeed OC

-   

Yellow LED

Return current to photovoltaic field:

The error occurs if the input voltage is particularly low 

(typically in the evening in conditions of low irradiation) 

and indicates a return current from the inverter to the 

photovoltaic panels).

If the error occurs in the evening or in conditions of low 

irradiation, it must not be considered a problem but a 

protection intervention for the photovoltaic field.

- If the error occurs with good irradiation conditions, switch 

the inverter off and back on again; if the error persists, contact 

customer assistance.

E103

- RSD self-test fault

-   

Yellow LED

RSD self-test fault:

RSD functionality is damaged

• Error inside the inverter and cannot be checked externally. 

- If the problem persists (once the inverter has been switched 

off and back on again), contact customer assistance.

Содержание PVS-60-TL-R-US















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды