manualshive.com logo in svg

ABB MTAC-01, Руководство пользователя

Поделиться
Скачать
ABB MTAC-01 Скачать руководство пользователя страница 5

5

Safety

Safety

Overview

This chapter states the general safety instructions that must be 
followed when installing and operating the MTAC-01 Pulse 
Encoder Interface module.

The material in this chapter must be studied before attempting any 
work on, or with, the unit.

In addition to the safety instructions given below, read the 
complete safety instructions of the specific drive you are working 
on.

General safety instructions

WARNING!

 All electrical installation and maintenance work on the 

drive should be carried out by qualified electricians.

The drive and adjoining equipment must be properly grounded.

Do not attempt any work on a powered drive. After switching off 
the input power, always allow the intermediate circuit capacitors 
5 minutes to discharge before working on the drive, the motor or 
the motor cable. It is good practice to check (with a voltage 
indicating instrument) that the drive is in fact discharged before 
beginning work.

The motor cable terminals of the drive are at a dangerously high 
voltage when input power is applied, regardless of motor 
operation. 

There can be dangerous voltages inside the drive from external 
control circuits even when the drive input power is shut off. 
Exercise appropriate care when working on the unit. Neglecting 
these instructions can cause physical injury or death.

Содержание MTAC-01





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды