manualshive.com logo in svg

ABB MTAC-01, Руководство пользователя

Поделиться
Скачать
ABB MTAC-01 Скачать руководство пользователя страница 23

23

Diagnostics

Diagnostics

Faults/Alarms

If the ACS350 detects that the encoder signal is lost, the drive 
operation and the diagnostic message are both controlled by 
parameter 

5003

 ENCODER FAULT:

•

5003

 = 1 (FAULT) – The drive generates a fault 

(23 ENCODER ERR), and the motor coasts to a stop.

•

5003

 = 2 (ALARM) – The drive generates an alarm 

(2024 ENCODER ERROR) and operates as if parameter 

5002

ENCODER ENABLE = 0 (DISABLE), that is, speed 

feedback is derived from the internal motor model.

In case of a fault or alarm signal, check for and correct the 
following:

Note: 

The validity of the encoder signal is also checked during the 

ID run. See parameter 9910 MOTOR ID RUN. If the drive detects 
an encoder problem during the ID run, the drive generates an 
alarm. Parameter 5003 ENCODER FAULT controls the drive’s 
fault/alarm response to encoder errors only after the ID run is 
completed.

CODE FAULT/ALARM

 1)

CAUSE

WHAT TO DO

0023

ENCODER ERR
(7301)
0306 bit 6

Communication fault 
between pulse encoder 
and pulse encoder 
interface module or 
between module and 
drive.

Check pulse encoder and its 
wiring, pulse encoder 
interface module and its 
wiring and parameter group 

50 ENCODER

 settings.

2024

ENCODER ERROR
(7310)
0309 bit 7

1)

 Name, code for fieldbus communication (in parentheses) and bit in fault/alarm word.

Содержание MTAC-01





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды