ABB MTAC-01 Скачать руководство пользователя страница 25

Страница: 25 / 28

Technical data

Ambient conditions

Temperature -10…+40°C (14…+104°F). No frost allowed.

Connectors

Connectors on the module:

• one 12-pin screw-type, non-detachable terminal block that

accepts wire connectors up to 1.5 mm

(16 AWG) for encoder

interface

• two RJ-45 connectors for panel pass-through

• 6-pin connector for drive interface

• grounding screw/stand-off for connection of the SCR terminals

of the drive and the MTAC-01 module.

Specifications

Module specifications

The MTAC-01 module:

• supports three channels: CH A, CH B, CH Z

• includes pass-through terminals to connect an external power

supply (required) to the pulse encoder

• has all of its materials UL-approved.

Channel specifications

Channel specifications:

• differential or single-ended

• maximum input frequency: 200 kHz

• input voltage range (measured at the MTAC module): see

Terminal designations

on page

• nominal input impedance (at 24 VDC): 20 kohm

• isolated from the logic and ground.

Содержание MTAC-01




























Результаты поиска

Содержание MTAC-01

Отзывы:

Бренды по названию

Популярные бренды

ABB MTAC-01, Руководство пользователя

Результаты поиска

Содержание MTAC-01

Отзывы:

Бренды по названию

Популярные бренды