ABB IRB 640 Скачать руководство пользователя страница 62

Страница: 62 / 152

Repairs

Axis 2

Product Manual IRB 640

3.3 Replacing lower arm

Refer to foldout nos. 1 and 1:1.

Dismounting:

Run the lower arm to the position where it is possible to secure the arm with

screws, through the holes for the lower fixing points of the balancing spring.

Dismount the balancing weight for axis 3.

Attach a hoist to the upper arm.

Remove the clamps, screws <1/3.160>, <1/3.142> and lift the parallel bar away.

Dismount the linkage according to Chapter 5, Link system.

Remove the cables in the lower arm as described in Chapter 3.8, Dismounting

cables, lower arm/upper arm.

Do not remove the cables from the upper arm.

Dismount the upper arm as described in Chapter 4.5, Dismounting upper arm,

complete.

Dismount the balancing unit <1:1/1> as described in Chapter 3.5, Dismounting

balancing unit or Chapter 3.6, Replacing guiding ring, balancing unit.

Attach a hoist to the under arm.

Dismount motor and gearbox for axis 2 as described in Chapter 3.2, Replacing the

gearbox.

10. Dismount motor and gearbox for axis 3 as described in Chapter 4.2, Replacing

gearbox.

11. Remove the 2 locking screws for the lower arm and gently lift the lower arm

together with the parallel arm, straight up.

12. Dismount the parallel arm as described in Chapter 4.3, Dismounting parallel arm.

Mounting:

13. Mount the parallel arm as described in Chapter 4.3, Dismounting parallel arm.

14. Lift the lower arm with mounted parallel arm in position.

15. First mount the motor and gearbox for axis 2, as in Chapter 3.2, Replacing the

gearbox.

Содержание IRB 640

























































































































































Результаты поиска

Содержание IRB 640

Отзывы:

Похожие инструкции для IRB 640

Бренды по названию

Популярные бренды

ABB IRB 640, Руководство по эксплуатации продукта

Результаты поиска

Содержание IRB 640

Отзывы:

Похожие инструкции для IRB 640

Бренды по названию

Популярные бренды