ABB IRB 640 Скачать руководство пользователя страница 74

Страница: 74 / 152

Repairs

Axis 3

Product Manual IRB 640

Remove the stop screws <1:1/137> in the lower arm.

Unscrew the shafts <1:1/203>. The bearing is pressed out with the shaft.

Note! Be careful with the threads on the shafts.

Lift the upper arm away.

Mounting:

Place the upper arm in position.

NOTE! Mount the left side first, complete, robot seen from behind!

10.

Mount sealing ring <1:1/140>, turn the largest diameter inwards.

11.

Mount the outer ring of the bearing in the upper arm.

12.

Mount the V-ring <1:1/134> on the shaft.

13.

Mount the shaft <1:1/203>. Lubricate the threads with Molycote 1000 and

tighten to a torque of 300 Nm.

14.

Apply Loctite 243 on stop screw <1:1/137> and tighten to torque 34 Nm.

15.

Insert the distance ring <1:1/138> on the shaft (only on the left side).

16.

Mount the bearing <1:1/133>.

17.

Insert the NILOS-ring <1:1/135> and distance ring <1:1/139>.

18.

Mount the KM nut. Apply Loctite 243 and tighten the nut, then loosen the nut

again and tighten to a torque of 90 Nm.

19.

Then mount the right side, paragraphs 12-18 (similar to the left side, except for

the distance ring <1:1/138). Just tighten the nut to 90 Nm.

20.

Mount the parallel bar. Use Molycote 1000 and tighten screws <1/3.143> for

the clamp with a torque of 300 Nm.

21.

Mount linkage as described in Chapter 5, Link system.

22.

Mount the cabling as described in Chapter 3.8, Dismounting cables, lower arm/

upper arm.

23.

Mount the balancing units as described in Chapter 3.5, Dismounting balancing

unit or Chapter 3.6, Replacing guiding ring, balancing unit.

NOTE! Remove the 2 extra mechanical stops!

Содержание IRB 640

























































































































































Результаты поиска

Содержание IRB 640

Отзывы:

Бренды по названию

Популярные бренды

ABB IRB 640, Руководство по эксплуатации продукта

Результаты поиска

Содержание IRB 640

Отзывы:

Бренды по названию

Популярные бренды