ABB IRB 640 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 152

background image

Calibration

Repairs

50

Product Manual IRB 640

- Not calibrated

One (or more) of the axes is NOT fine-calibrated. This or these axes, must
therefore be fine-calibrated as described in Chapter 9.2, Calibration proce-
dure.

20. If there is more than one unit, select the desired unit in the window in Figure 14.

Choose Calib: Calibrate and the window shown in Figure 15 will appear.

Figure 15 The dialog box used to calibrate the manipulator.

21. Press the function key All to select all axes, if all axes are to be commutated.

Otherwise, select the desired axis and press the function key Incl (the selected axis

is marked with an x).

22. Confirm by pressing OK. The window in Figure 16 appears.

Figure 16 The dialog box used to start the calibration.

23. Start the calibration by pressing OK.

An alert box is displayed during calibration.
The Status window appears when the fine calibration is complete. The revolution
counters are always updated at the same time as the calibration is performed.

Incl

All

Cancel

OK

1(6)

Calibration!

Robot

To calibrate, include axes and press OK.

Axis

Status

X

1

Not Fine Calibrated

X

2

Not Fine Calibrated

3

Fine Calibrated

4

X

5

X

6

Not Fine Calibrated

Cancel

OK

Calibration!

Robot

- - - - - WARNING - - - - -

The calibration for all marked axes

will be changed.

It cannot be undone.

OK to continue?

«
...
91
92
93
94
95
...
»

Содержание IRB 640

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для IRB 640

Бренд: ABB Страницы: 1008

Бренд: artisan Страницы: 15

Бренд: ZKTeco Страницы: 33

Бренд: Hiwonder Страницы: 16

Бренд: Hiwin Страницы: 16

Бренд: Hiwonder Страницы: 42

Бренд: Hiwin Страницы: 51

Бренд: Hiwin Страницы: 52

Бренд: Hiwin Страницы: 64

RA610-GB Series

Бренд: Hiwin Страницы: 70

Бренд: Hiwin Страницы: 70

SCARA Robot RS405-LU

Бренд: Hiwin Страницы: 125

Solar Cosmonaut

Бренд: Arexx Страницы: 2

Бренд: Arexx Страницы: 30

SKY WALKER SW-007

Бренд: AREXX Engineering & JM3 Engineering Страницы: 34

Бренд: AREXX Engineering & JM3 Engineering Страницы: 67

Бренд: Arexx Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды