ABB IRB 640 Скачать руководство пользователя страница 77

Страница: 77 / 152

Link system

Repairs

Product Manual IRB 640

Mounting:

Lower rod

The bearings can take a skew setting. But be careful.

14.

Apply Loctite on the shaft before mounting the ring <205.31>, see foldout 1:4

view D-D and E-E. Mount ring <205.31> on both the upper and lower shaft.

15.

Mount the lower rod <205.20> with bearings <205.21>.

16.

Refill the bearing with grease.

17.

Mount KM-nut <205.6> at the upper shaft. Tighten to 50 Nm.

18.

Mount friction washer <205.32>, support washer <205.28> and screw

<205.29> use Loctite 243.

19.

Mount a new cover <205.24>.

Upper rod

Note! When changing bearing, pushing a bearing is only allowed on its text
side. The other side is not hard enough.

20.

Place ring <205.4>, support ring <205.5>, sealing ring <205.3> and the inner

races of the bearings on the front and rear shaft. Grease the bearing.

21.

Mount the upper rod <205.1>.

22.

Mount sealing ring <205.3>, support washer <205.5> and KM-nuts <205.6>,

use Loctite 243. Tighten to a torque of 50 Nm.

23.

Calibrate the robot as described in Chapter 9, Calibration.

Tightening torque:

KM-nut, item 205.6:

50 Nm

Содержание IRB 640

























































































































































Результаты поиска

Содержание IRB 640

Отзывы:

Бренды по названию

Популярные бренды

ABB IRB 640, Руководство по эксплуатации продукта

Результаты поиска

Содержание IRB 640

Отзывы:

Бренды по названию

Популярные бренды