manualshive.com logo in svg

ABB IRB 640, Руководство по эксплуатации продукта

Поделиться
Скачать
ABB IRB 640 Скачать руководство пользователя страница 44

Repairs

CONTENTS

Page

Product Manual IRB 640

1

1  General Description ........................................................................................................ 3

1.1  Document Guidance ............................................................................................... 5

1.2  Caution.................................................................................................................... 6

1.3  Mounting Instructions for Bearings and Seals ....................................................... 6

1.3.1  Bearings ....................................................................................................... 6

1.3.2  Seals ............................................................................................................. 7

1.4  Instructions for Tightening Screw Joints ................................................................ 9

1.5  Tightening Torques ................................................................................................. 10

1.5.1  Screws with slotted or cross recessed head.................................................. 10

1.5.2  Screws with hexagon socket head................................................................ 10

2   Axis 1 ............................................................................................................................... 11

2.1  Replacement of motor ............................................................................................ 11

2.2  Cabling axis 1 ......................................................................................................... 12

2.3  Replacing the gearbox ............................................................................................ 14

2.4  Dismounting joint bearing ...................................................................................... 15

2.5  Dismounting cooling axis 1 .................................................................................... 16

3  Axis 2 ................................................................................................................................ 17

3.1  Replacing motor ..................................................................................................... 17

3.2  Replacing the gearbox ............................................................................................ 18

3.3  Replacing lower arm............................................................................................... 19

3.4  Replacing bearing in lower arm.............................................................................. 20

3.5  Dismounting balancing unit.................................................................................... 21

3.6  Replacing guiding ring, balancing unit................................................................... 23

3.7  Replacing bearings, balancing unit......................................................................... 24

3.8  Dismounting cables, lower arm/upper arm............................................................. 25

4  Axis 3 ................................................................................................................................ 27

4.1  Replacing motor ..................................................................................................... 27

4.2  Replacing gearbox .................................................................................................. 28

4.3  Dismounting parallel arm ....................................................................................... 29

4.4  Replacing parallel bar with bearings ...................................................................... 29

4.5  Dismounting upper arm, complete ......................................................................... 30

5  Link system ...................................................................................................................... 33

5.1  Replacing upper and lower rod............................................................................... 33

5.2  Replacing the link ................................................................................................... 35

Содержание IRB 640

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды