manualshive.com logo in svg

ABB Foundation LD 810HSE Ex, Быстрое руководство по установке

Поделиться
Скачать
ABB Foundation LD 810HSE Ex Скачать руководство пользователя страница 4

4  Quick Installation Guide LD 810HSE Ex | 

2PAA118721

Section 1  Introduction ........................................................................................... 5

Intended use ......................................................................................................... 6

Section 2  Installation ............................................................................................. 7

Installation in Hazardous Locations ........................................................................ 7
General Requirements ........................................................................................... 8
Hazardous Location - North American Approval (cULus) ...................................... 11
Hazardous Location - European and International Approval (ATEX, IECEx) ........... 12
Mounting and Dismounting .................................................................................. 13
Connection Diagram ............................................................................................ 15
Connecting the Power Supply ............................................................................. 16
Ethernet Ports ..................................................................................................... 17
Redundancy Link Interface .................................................................................. 18
FF-H1 Interfaces ................................................................................................. 20
Configuring LD 810HSE Ex .................................................................................. 22

Section 3  Status Indicators - LEDs ..................................................................... 23

LED Indicators in Stand-Alone Mode (RUN and ERR) ........................................... 24
LED Indicators in Redundant Mode (RUN, ERR, and RDL) ................................... 25
Status Indications of the 4 H1 Channels .............................................................. 29

Section 4  Specifications ...................................................................................... 30

Section 5  Manufacturer‘s Declaration ................................................................. 33

Table of Contents

Содержание Foundation LD 810HSE Ex





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды