manualshive.com logo in svg

ABB Foundation LD 810HSE Ex, Быстрое руководство по установке

Поделиться
Скачать
ABB Foundation LD 810HSE Ex Скачать руководство пользователя страница 22

22  Quick Installation Guide LD 810HSE Ex | 

2PAA118721

Configuring LD 810HSE Ex

Although the Linking Device is delivered with a pre-configured IP address 
(192.168.0.10), it must be assigned an IP address from your LAN address 
range. Furthermore, subnet mask and gateway IP address must be set accord-
ingly. This information is referred to as IP configuration.

The IP configuration can be changed via Ethernet by means of a web browser 
(HTTPS protocol, recommended). See the User Manual (2PAA114135-610) for 
the password of the web server interface. In addition, if a DHCP server is avail-
able, the LD 810HSE Ex can be configured to use a DHCP address.

Make sure that the LD 810HSE Ex and the PC are in the same 
network. 

For commissioning of LD 810HSE Ex, refer to the LD 810HSE Ex 
User Manual (2PAA114135-610) available in the MyABB portal 
(https://myportal.abb.com/home).

Before commissioning of LD 810HSE Ex, make sure to use the 
latest and recommended Linking Device firmware released for your 
system environment.

Содержание Foundation LD 810HSE Ex





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды