manualshive.com logo in svg

ABB Foundation LD 810HSE Ex, Быстрое руководство по установке

Поделиться
Скачать
ABB Foundation LD 810HSE Ex Скачать руководство пользователя страница 33

2PAA118721 

| Quick Installation Guide LD 810HSE Ex  33 

Section 5  Manufacturer‘s Declaration

This device complies with the requirements of the EC directive 2014/30/EU, 
“Electromagnetic Compatibility” (EMC directive). It meets the following harmo-
nized standards:

 

– EN 55011 - Industrial, scientific and medical (ISM) devices - radio 

disturbance - limits and methods of measurement

 

– EN 55032 - Electromagnetic compatibility of multimedia equipment (MME) 

and interference emission

 

– EN 61000-6-4 - Electromagnetic compatibility (EMC); part 6-4: generic 

standard – Emission standard for industrial environments

 

– EN 61000-6-2 - Electromagnetic compatibility (EMC); part 6-2: generic 

standard - Immunity for industrial environments

To fulfill the EMC requirements, the other components of your 
installation (DC adapter, Industrial Ethernet devices, etc.) also have 
to meet the EMC requirements. A shielded cable must be used. In 
addition, the cable shield must be grounded properly.

RoHS

The LD 810HSE Ex device is RoHS compliant. 

WEEE

Electrical and electronic equipment must be disposed of separately 
from normal waste at the end of its operational lifetime. Packaging 
material and worn components shall be disposed of according to 
the regulations applicable in the country of installation.

Содержание Foundation LD 810HSE Ex





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды