manualshive.com logo in svg

ABB Foundation LD 810HSE Ex, Быстрое руководство по установке

Поделиться
Скачать
ABB Foundation LD 810HSE Ex Скачать руководство пользователя страница 16

16  Quick Installation Guide LD 810HSE Ex | 

2PAA118721

If ambient temperatures exceed 55 °C at the place of installation, it 
may occur that the temperatures of connecting cables strongly rise 
if those cables have been put in place in an unfavorable condition. 
In such cases, either perform measurements to confirm that the 
service temperature of the cables is not exceeded (i. e. 80 °C), or 
use such cable variants that withstand temperatures of minimum 
90 °C.

Connecting the Power Supply

The supply voltage (18 V DC ... 32 V DC) is connected by a 3-pole terminal 
block. The power supply is connected to the plug connector via flexible wires 
with a cross section of 0.75 to 1.5 mm². The ground connection wire must have 
a cross section of 1.5 mm².

Pin

Signal

Description

1

GND

Ground

2

Functional Earth

3

L+

Positive supply voltage

The Functional Earth (FE) connection of the device has to be 
connected at low inductance with the Protective Earth (PE) of the 
system.

Содержание Foundation LD 810HSE Ex





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды