ABB FET630 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 92

background image

30

FEP630, FEH630

ELECTROMAGNETIC FLOWMETER | CI/FEP630/FEH630-EN REV. D

… 5 Electrical connections

… Connection with IP rating IP 68

Electrical connection

NOTICE

Adverse effect on the IP rating IP 68

The IP rating IP 68 of the sensor may be adversely affected as
a result of damage to the signal cable.
• The sheathing of the signal cable must not be damaged.

1. Use the supplied signal cable to connect the sensor and the

transmitter.

2. Connect the signal cable in the terminal box of the sensor.
3. Route the cable from the terminal box to above the maximum

flooding height of 5 m (16.4 ft).

4. Tighten the cable gland.
5. Carefully seal the terminal box. Make sure the gasket for the

cover is seated properly.

Note

As an option, the sensor can be ordered with the signal cable
already connected to the sensor and the terminal box already
potted.

Potting the terminal box on-site

CAUTION

Danger to health!

The two-component potting compound is toxic – observe all
relevant safety measures!
Comply with the safety data sheet of the two-component
potting compound before preparations are started.

Risk notes:

• R20: Damaging to health when inhaled.
• R36/37/38: Irritates the eyes, respiratory organs and

the skin.

• R42/43: Sensitization through inhaling and skin

contact is possible.

Safety advice:

•  S23: Do not inhale gas/smoke/humidity/aerosol.
•  S24: Avoid contact with the skin.
•  S37: Wear suited protective gloves.
•  S63: In case of an accident due to inhaling: take the

injured person out into the fresh air to rest.

If the terminal box is to be potted subsequently on-site, a special
two-component potting compound can be ordered separately
(order no. D141B038U01). Potting is only possible if the sensor is
installed horizontally. Observe the following instructions during
work activity:

Preparation

• Complete the installation before potting in order to avoid

moisture penetration. Before starting, check all the
connections for correct fitting and stability

• Do not overfill the terminal box. Keep the potting compound

away from the O-ring and the gasket / groove (see
Figure 39).

• Prevent the two-component potting compound from

penetrating the cable conduit (Conduit) for an ½ in NPT
installation (if used).

Procedure

G12152

1

2

3

4

5

1

Packaging bag

2

Connection clamp

3

Two-component potting

compound

4

Drying bag

5

Maximum fill level

Figure 39: Terminal box sealing

1. Cut open the protective enclosure of the two-component

potting compound (see packing).

2. Remove the connection clamp of the potting compound.
3. Knead both components thoroughly until a good mix is

reached.

4. Cut open the bag at a corner. Perform work activity within

30 minutes.

5. Carefully fill the terminal box with the two-component

potting compound until the connection cable is covered.

6. Wait a few hours before closing the cover in order to allow

the compound to dry, and to release any possible gas.

7. Ensure that the packaging material and the drying bag are

disposed of in an environmentally sound manner.

Change from two to one column

«
...
28
29
30
31
32
...
»

Содержание FET630





























































































Отзывы:

Нет отзывов

Похожие инструкции для FET630

Disklavier Mark III Series

Бренд: Yamaha Страницы: 39

Бренд: Armstrong Monitoring Corporation Страницы: 12

Бренд: Veeco Страницы: 349

Бренд: GrainPro Страницы: 7

Бренд: Caen Страницы: 50

Бренд: OHAUS Страницы: 6

Fusion-L 6 digit

Бренд: London Electronics Страницы: 44

Бренд: Xsensor Страницы: 13

Бренд: RAM Страницы: 43

Бренд: ScienTECH Страницы: 43

Бренд: LOVATO ELECTRIC Страницы: 9

Бренд: Samick Страницы: 48

Бренд: Hanna Instruments Страницы: 2

Бренд: Medical International Research Страницы: 46

Бренд: Fluke Страницы: 32

Бренд: MSA Страницы: 3

Бренд: Andor Technology Страницы: 2

DOUBLE VISION DDPM-40

Бренд: Global Test Supply Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды