ABB FET630 Скачать руководство пользователя страница 63

Страница: 63 / 92

FEP630, FEH630

ELECTROMAGNETIC FLOWMETER | CI/FEP630/FEH630-EN REV. D

Exiting the setup

For some menu items, values must be entered. If you don't want
to change the parameter, you can exit the menu as described
below.
1. Pressing

(Next) repeatedly moves the cursor to the right.

Once the cursor reaches the end position, ‘Cancel’ is
displayed in the lower right of the screen.

terminates editing and exits the menu item. Use

return to the start.

Note

The LCD display automatically returns to the process display
three minutes after the last button has been actuated.

Brief overview of configurations

Configuration of digital output 41 / 42 as pulse output for
forward flow and digital output 51 / 52 as pulse output for
reverse flow.

Menu / parameter

Parameter setting

Input/Output / Dig.Out 41/42 / …

Mode

Pulse

Outp. Flow Direction

Forward

Input/Output / ...Setup Pulse Output

Output Value Pulse

Pulse

Volume

Flow

Pulses per Unit

Setting in accordance with

requirement

Pulse Width

Setting in accordance with

requirement

Input/Output / Dig.Out 51/52

Mode

41/42

Extended diagnostic functions

Overview

Note

• The extended diagnostic functions are only available on the

ProcessMaster FEP630 and HygienicMaster FEH630 if the
‘Extended diagnostic functions’ software package has been
ordered (see table) .

• The ‘Partial Filling Detector’ function is

not

available for

HygienicMaster FEH630.

• To facilitate initial commissioning, the individual diagnosis

options of the extended diagnostic functions are deactivated
(factory default).

• Each diagnostic function (e.g. Gas Bubble Detector or

Electrode Deposit Detector) can be individually activated.
Once activated, the diagnostic function must be calibrated
according to the conditions on site and the limit values must
be set.

Diagnostic Functions

Standard

Empty pipe detection (EPD)

Partial filling detection (TFE)

Noise / grounding check

Fingerprint

verification

Service

interval

Transmitter

temperature

Software package ‘Extended
diagnostic functions’ (optional)

Coil/sensor temperature

Coil inductance

Gas

bubble

detection

Conductivity

monitoring

Electrode impedance / Leakage

Monitoring

Filling function (optional)

Filling function

Содержание FET630





























































































Результаты поиска

Содержание FET630

Отзывы:

Бренды по названию

Популярные бренды

ABB FET630, Руководство пользователя

Результаты поиска

Содержание FET630

Отзывы:

Бренды по названию

Популярные бренды