ABB FET630 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 92

ABB FET630 Скачать руководство пользователя страница 69

FEP630, FEH630

ELECTROMAGNETIC FLOWMETER | CI/FEP630/FEH630-EN REV. D

69

10

Specification

Note

The device data sheet is available in the ABB download area at

www.abb.com/flow

.

Permitted pipe vibration

In accordance with EN 60068-2-6
Valid for sensors in remote mount and integral mount design.
• Maximum deflection: 0.15 mm (0.006 in) in the frequency

range of 10 to 58 Hz

• Maximum acceleration: 2 g in the frequency range of

58 to 150 Hz

ProcessMaster – Temperature data

The temperature range offered by the device is dependent on a
number of different factors.
These factors include the measuring medium temperature
T

medium

, the ambient temperature T

amb

, operating pressure

P

medium

, liner material and the approval for explosion protection.

Storage temperature range

Æ

40 to 70 °C (

Æ

40 to 158 °F)

Maximum permissible cleaning temperature

CIP media

Liner

Cleaning temperature

Steam

PTFE, PFA

150 °C (302 °F)

Cleaning fluid

PTFE, PFA

140 °C (284 °F)

• The maximum cleaning temperature specified applies to a

maximum ambient temperature of 25 °C (77 °F).

If the ambient temperature up-scales > 25 °C (> 77 °F), then
the temperature difference to the current temperature must
be subtracted from the max. cleaning temperature.

• The specified cleaning temperature may have an effect for a

maximum of 60 minutes.

Change from two to one column

«
...
67
68
69
70
71
...
»

Содержание FET630





























































































Отзывы:

Нет отзывов