ABB Conceptpower DPA 500 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 114

background image

Modifications reserved

Page 27/94

4.3.4

DC wiring instructions

In the UPS-cabinet of the Conceptpower DPA 500 there is no space provided for batteries, therefore

the battery will be external in either in cabinets or in shelves/racks.
Batteries can be either separate for each module or common battery within the same frame. It is normally

recommended for redundant Multi-Module systems to provide each UPS-Module with its own separate battery.

Before proceed with the wiring, make sure you have read and understood the chapter

4.2 Electrical installation.

WARNING

KEEP OUT OF BATTERY POLES WHICH CONTAIN DANGEROUS DC-

VOLTAGES CAUSING FATAL ACCIDENTS.
DO NOT OPERATE IN CASE OF PRESENCE OF WATER OR MOISTURE. BY

OPENING OR REMOVING THE UPS-COVERS YOU RUN RISK OF
EXPOSURE TO DANGEROUS VOLTAGES!
MANIPULATION ON THE BATTERY SYSTEM SHOULD ONLY BE DONE BY
TRAINED SERVICE AND MAINTENANCE PERSONEL OF THE

MANUFACTURER OR HIS AUTHORISED SERVICE PARTNERS.
INAPPROPRIATE MANIPULATIONS OF THE BATTERIES CAN CAUSE

LIGHTNING SPARKS. WHILE OPERATING ON BATTERY SYSTEMS IT IS
MANDATORY TO WEAR GLASSES

To ensure protection of the personnel during the installation of the UPS make sure that the

connections are performed under the following conditions:

•

No mains voltage is present in the UPS

•

All the loads are disconnected

•

The UPS and the external battery are voltage-free

To verify the complete shutdown of the Conceptpower DPA 500 perform following steps:

•

No mains voltage is present

•

All Loads are shut down and disconnected

•

UPS is shut down and voltage-free

•

Maintenance Bypass IA1 is open and in position OFF;

•

All 5xparallel Isolators IA2-1, IA2-2, IA2-3, IA2-4, IA2-5 are in position OFF (open)

•

All 5xbattery breakers F3-1, F3-2, F3-3, F3-4, F3-5 are in position OFF (open)

•

Make sure the battery fuses in the external battery cabinet and on the UPS are open.

Achieve the DC battery wiring according to the following instructions, by making sure the correct
wires are used and the cables are tightened with the correct torque, as stated in the tables 8 and 10:

1.

COMMON BATTERY – Connect the PE wire(s) and then connect the battery wires, make

sure the polarity (+) and (-) is respected!

Common battery, bottom cable entry

Common battery, Top cable entry

«
...
25
26
27
28
29
...
»

Содержание Conceptpower DPA 500



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Conceptpower DPA 500

Бренд: MAKELSAN Страницы: 45

UNINTERRUPTIBLE POWER SUPPLY MODELS SG1K-2T

Бренд: Falcon Страницы: 9

Бренд: LC Страницы: 2

Бренд: Konig Страницы: 88

5SC 1000i Rack2U

Бренд: Eaton Страницы: 20

Бренд: Eaton Страницы: 28

Бренд: HELIOR Страницы: 26

SmartPro SMART750RM1U

Бренд: Tripp Lite Страницы: 5

Бренд: Power Sentry Страницы: 2

Бренд: Xtreme Power Conversion Страницы: 77

Бренд: Tripp Lite Страницы: 36

Бренд: Tripp Lite Страницы: 96

Бренд: nedis Страницы: 112

Бренд: Panamax Страницы: 20

SPS SOHO+ series

Бренд: Salicru Страницы: 20

Бренд: FSP Technology Страницы: 28

Бренд: Cover Страницы: 44

Бренд: Cover Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды