manualshive.com logo in svg

ABB C1900RC, Руководство по эксплуатации

Поделиться
Скачать
ABB C1900RC Скачать руководство пользователя страница 4

2

Calibration Test

  carries out check of non-volatile

memories containing the calibration data for each analog
input and output, then indicates pass or fail – see 

Error

Codes

 below.

or

CAL
FAIL

CAL
PASS

Configuration Test

 carries out check of non-volatile

memories containing the instrument configuration, then
indicates pass or fail – see 

Error Codes

  below.

or

CONFIG

FAIL

CONFIG

PASS

CPU Test

 carries out check of processor circuitry – see

Error Codes

 below.

or

CPU

FAIL

CPU

PASS

Instrument Test

 identifies the instrument type, e.g.

1914r – see Table 2.1 in the

 

Installation Manual

.

1914 r

tESt

or

Battery Back RAM Test

 carries out check of battery-

backed RAM, then indicates pass or fail – see 

Error

Codes

 below.

bb rAM
PASS

bb rAM
FAIL

Error Codes

 are

displayed in the event
of a fault – see Section
2.1.1.

or

Normal Display

A––––F
–2–4––

AL

RMT

AT

MAN

Lined Failed 

indicates power failure

and is cleared when advancing to the
next frame or page.

AL

RMT

AT

MAN

Flashing

between

Not applicable on single
channel instruments

  !00.3
  100.3

 LINE

FAILEd

Red Pen

(Channel 1)

Green Pen

(Channel 2)

Blue Pen

(Channel 3)

Black Pen

(Channel 4)
– see 

Note

0.35 (8.8)

Chart Time Line

Dimensions in inches (mm)

0.175 (4.4)

0.175 (4.4)

2

SETTING UP

2.1

Instrument Power-up – Fig. 2.1 and 2.2

Caution.

Ensure that all connections, especially to the

earth stud, are made correctly.

a) Check that the input sensors are installed correctly.

b) Check that the pen(s) are installed correctly – see Fig. 2.1.

c) Switch on the supply to the instrument, any power-operated

control circuits and the input signals. Wait for the pens to
settle.

Note.

On power-up, the pens are moved to an off-

chart position for automatic referencing. Pen chatter
may occur on those pens nearest the reference
position. 

This is a normal function of the instrument.

d) The start-up sequence shown in Fig. 2.2 is displayed on

faceplate 1 when the supply is first switched on.

Fig. 2.2 Instrument Displays at Start-up

Fig. 2.1 Checking the Pen(s) Installation

Note.

If the true time line event option is fitted, the

violet event pen records on the same time line as
the red pen, but on the outer edge of the chart.

Содержание C1900RC













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды