ABB C1900RC страница 33 Скачать руководство пользователя

Страница: 33 / 44

Heat
Output
(%)

Cool

Output

(%)

100

Max. Cool
Output = 75%*

Max. Heat
Output = 88%*

100

Q Heater = 1.5kW

Q Cooler = 0.75kW

Output Off

Hysteresis Band

=15%*

*User definable limits

Transition

Bandwidth

20%

Proportional Band

(Cool) 25.0%

Integral Action Value

(Cool)

Derivative Action Value

Proportional Band
(Heat) 20.0%

Integral Action Value
(Heat)

Derivative Action Value

100%

PID Output (%)

Crossover Value (33%)

CONTROL OPERATION…

5.10

Introduction to Heat/Cool Control

Note.

Refer to Sections 5.10.2 and 5.10.3 for Crossover Value and Transition Bandwidth Value examples.

Information.
• PID Output

– is the output value calculated by the controller. The output is divided into two different control elements one

for raising the product temperature (heat output) and one for lowering the product temperature (cool output).

•

Transition Bandwidth

– used to transfer smoothly from one set of control terms to the other.

•

Crossover Value

– defines the changeover point between heat output active and cool output active. The crossover value

is also the centre of the transition and off hysteresis bands.

•

Output Off Hysteresis Band

– for the majority of applications Outputs 1 and 2 have opposing control actions i.e. one is

direct acting and the other is reverse. In this configuration both outputs are at 0% within the off hysteresis band. The band
setting is used to prevent oscillation of control changes.

•

Heat/Cool Outputs

– refer to

PID Output

, above.

Fig. 5.18 Heat/Cool Control – Principle of Operation

Содержание C1900RC













































Результаты поиска

Содержание C1900RC

Отзывы:

Похожие инструкции для C1900RC

Бренды по названию

Популярные бренды

ABB C1900RC, Руководство по эксплуатации

Результаты поиска

Содержание C1900RC

Отзывы:

Похожие инструкции для C1900RC

Бренды по названию

Популярные бренды