manualshive.com logo in svg

ABB C1900RC, Руководство по эксплуатации

Поделиться
Скачать
ABB C1900RC Скачать руководство пользователя страница 3

1

Part No.

IM/C1900–INS

INSTALLATION

Product Identification

Siting

Mounting

Electrical Connections

Installation Record

OPERATION

Setting Up

Error Messages

Operating Level

Simple Fault Finding

PROGRAMMING

General Programming

Basic Config. Level

Control Config. Level

Advanced Config. Level

Connections and Links

DATA SHEET

Full Specification

Part No.

IM/C1900–OGC

Displays & Controls

Part No.

IM/C1900–PGC

Part No.

SS C1900

Flow Totalization

Ramp/Soak Profile

Math Functions

Timer Functions

MODBUS (RTU)

Serial Adaptors

Serial Connections

Programming Pages

ASCII Tables

Part No.

IM/C1900–ADV

Part No.

IM/C1900–MOD

ADVANCED SOFTWARE

OPTIONS

A – Standard Manuals

B – Supplementary Manuals

CONTENTS

1

INTRODUCTION

The documentation for the C1900 series of circular chart
recorders is shown in Fig. 1.1. The 

Standard Manuals

, including

the specification sheet, are supplied with all instruments. The

Supplementary Manuals

 supplied depend on the specification of

the instrument.

Fig. 1.1 C1900 Documentation

Section

Page

1

INTRODUCTION ........................................................... 1

2

SETTING UP ................................................................. 2

2.1

Instrument Power-up .......................................... 2
2.1.1

Power-up Error Codes .......................... 3

2.2

Fitting the Chart .................................................. 4

2.3

Fitting the Pen Capsule(s) ................................... 4

3

DISPLAYS & CONTROLS ............................................. 5

3.1

Displays and LED Indicators ............................... 5

3.2

Use of Controls ................................................... 7

4

GENERAL OPERATION ................................................ 8

4.1

Input Error Messages .......................................... 9

5

CONTROL OPERATION ............................................. 10

5.1

Operating Page Introduction ............................. 12
5.1.1

Set Point Tracking ............................... 12

5.1.2

Auto/Manual Transfer .......................... 12

5.1.3

Profile Control ..................................... 12

5.1.4

Cascade Control ................................. 12

5.1.5

Heat/Cool Control ............................... 12

5.2

Operating Page Displays ................................... 13

5.3

Alarm Acknowledge Page ................................. 16
5.3.1

Alarm Indications ................................. 16

5.3.2

Acknowledging Alarms ........................ 16

5.3.3

Using the Alarm
Acknowledge Page ............................. 16

5.4

Totals Page Displays ......................................... 17

5.5

Access to Configuration Levels ......................... 18
5.5.1

Security Code Page ............................ 18

5.6

Profile States Page ........................................... 19

5.7

Auto-tuning Introduction ................................... 20
5.7.1

Auto-tuning Page ................................ 21

5.8

Auto-tune Diagnostic Messages ....................... 24

5.9

Introduction to Standard Control ....................... 25
5.9.1

Control Page (Standard Control) .......... 30

5.10

Introduction to Heat/Cool Control ..................... 31
5.10.1

Control Page (Heat/Cool Control) ........ 32

5.10.2

Calculating the Crossover Value .......... 33

5.10.3

Calculating the Transition
Bandwidth Value ................................. 33

6

RECORD OPERATION ............................................... 34

6.1

Operating Page Displays ................................... 35

6.2

Alarm Acknowledge Page ................................. 36
6.2.1

Alarm Indications ................................. 36

6.2.2

Acknowledging Alarms ........................ 36

6.2.3

Using the Alarm
Acknowledge Page ............................. 36

6.3

Totals Page Displays ......................................... 37

7

SIMPLE FAULT FINDING ........................................... 38

8

SPARES LIST ............................................................. 39

Содержание C1900RC













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды