ABB C1900RC Скачать руководство пользователя

Страница: 21 / 44

SKIP–b

PrOFLE

ProGrM

SEG xx
SKIP–F

rESEt

SKIP–F

OFF

SKIP–N

StAtES

YES

rS–End

rS–Hld

rS–run

rS–OFF

StAtES

ProFLE

rUN

YES

NO (if program running)

SKIP–N

HOLd

rUN

(if program

not running)

SKIP–b
SKIP–F

CONTROL OPERATION…

5.6

Profile States Page

Page Header –

Profile States

The

key can be programmed to jump to this frame (

Set Up Function Keys

Page

ADVANCED CONFIGURATION LEVEL

). If the key is used, the display reverts

automatically to the first frame of the

Operating Page

when leaving this page.

Program Select

Select the program to be run (1 to 10).

Profile Status (Ramp Soak)

rS–OFF

– (Ramp Soak Run/Off)

select

rUN

to start selected program.

Press the

key to activate.

rS–rUN

HOLd

– (Ramp Soak Run/Hold) select

HOLd

to stop selected program

at current level.
Press the

key to activate.

rS–Hld

– (Ramp Soak Hold) program is in the hold state, either as a result

of an operator hold, the controller is in manual or the holdback
facility (guaranteed ramp/soak). Select run to continue running
the profile if operator has stopped program. Press the

key

to activate.

rS–HLd

ENd

– (Run/Hold End)

the profile is completed, and the digital input

assigned to the profile function is still in the 'Run' state. This
frame is only displayed if a digital input is used to run and hold
the profile.

Note.

If a digital input is assigned to the run/hold function, the user is prevented from

overriding the digital signal.

Profile Reset

If the profile is running and

YES

is selected, the profile returns to the beginning of the

program and continues to run.

Note.

To end a program, select

HOLd

at the Profile Status frame (see above) and

then select

YES

at this frame. The local set point value takes the value of the first level

of the selected program.

Skip Segment

The segment number (or

End

) is shown in the upper display.

SKIP–F

(skip forward) – abandon current segment and start next segment.

SKIP–N

(do not skip) – maintain control using current segment.

SKIP–b

(skip back) – return to beginning of current segment.

For multiple skip operations, the last selection (For b) is displayed for 3 seconds
before reverting to

SKIP–N

Содержание C1900RC













































Результаты поиска

Содержание C1900RC

Отзывы:

Похожие инструкции для C1900RC

Бренды по названию

Популярные бренды

ABB C1900RC, Руководство по эксплуатации

Результаты поиска

Содержание C1900RC

Отзывы:

Похожие инструкции для C1900RC

Бренды по названию

Популярные бренды