AB Inflatables ABJET 285 Скачать руководство пользователя

Страница: 9 / 47

KNOWING YOUR ABJET

TENDER

JET BOATS SAFETY / IDENTIFICATION NUMBER

Jet Boat Safety

WARNING

An ABJET® may perform differently to other boats you may

have ridden in the past. Take time to familiarize yourself with

your new boat.

Always keep in mind that as the throttle lever is returned to

the idle position, less directional control is available. To turn

the jet boat, both steering and throttle are necessary.

•Boats in general have no brake. Stopping distance will vary

depending on initial speed, load, wind, and water conditions.

Practice stopping and docking in a safe, traffic-free area to get

a sense of how long it will take to stop the boat under varying

conditions.

•

Do not release the throttle when trying to steer away from

objects. You need throttle to steer.

•Do not use the reverse to stop.

•In shallow waters, proceed with caution and at very low

speeds. Grounding or abrupt stops may result in injury to

you, your passengers or others. The jet pump may pick up

debris and throw it forward causing a risk of injuring people

or damaging the jet pump or other property.

•Do not add accessories or equipment that may adversely

affect visibility or alter control of the boat.

•Engine exhaust contains carbon monoxide (CO), which can

cause injury or death if inhaled in sufficient quantities.

Educate all occupants about the risks and symptoms of CO

accumulation and CO poisoning.

•

If, at any time, gasoline leaks/odors are found, do not start

the engine.

Identification Number

Safeguard the information about your boat by recording the

hull identification number (HIN). The HIN is located on the

upper starboard corner of the transom. The HIN must be

clearly visible at all times and must not be removed, altered or

tampered with in any way. The identification number is very

important! Keep a copy of this number stored in a safe place

off the boat in case of theft, damage, warranty claims, etc.,

report this number to the local authorities, your insurance

agent and your dealer.

Содержание ABJET 285
















































Результаты поиска

Содержание ABJET 285

Отзывы:

Похожие инструкции для ABJET 285

Бренды по названию

Популярные бренды

AB Inflatables ABJET 285, Руководство пользователя

Результаты поиска

Содержание ABJET 285

Отзывы:

Похожие инструкции для ABJET 285

Бренды по названию

Популярные бренды