AB Inflatables ABJET 285 Скачать руководство пользователя

Страница: 33 / 47

USE & PERFORMANCE OF YOUR ABJET

TENDER

TOWING YOUR INFLATABLE

Towing valve in closed position

Ensure water flows out of jet pump while flushing. Otherwise,

refer to an authorized ABJET® Service Center for servicing.

Towing valve in opened position

WARNING

•

Never tow a boat with people on board.

•

Towing or being towed stresses the boats, hardware and lines.

Failure of any part can seriously injure people or damage the boats.

•

Never use three-stand twisted nylon; it has too much elasticity and

can snap back dangerously. Because of the tremendous stress

caused by towing, use a tow line rated at least 4 times the gross

weight of the boat being towed.

CAUTION

Do not attach the towing line to the bow grab handle or any other

accessory not designed for that purpose.

•

Tow ropes must always be in good condition, free of any cuts or

abrasions.

•

When attaching the tow line to a fitting, be sure the fitting is fastened

securely and trough-bolted.

•

The (CSM) coated fabric handles must not be used for towing.

•

Keep the towing boat and the inflatable tender on the crest or in the

trough of the waves at the same time. In protected, calm waters,

shorten the line for better handling.

•

Never attempt to tow a much larger or grounded vessel.

•

Always tow at moderate speed so as to prevent sudden strain on

slack line.

•

Keep hands and feet clear of the other boat.

•

Never hold a towline after it is pulled taut.

•

The boat structure can be damaged by excessive pulling strain.

•

Be ready to cast loose or cut the line if the towing situation becomes

hazardous.

DANGER

Do not allow anyone to be in line with the tow rope. If the rope should

break or pull free, dangerous recoil could occur which may cause

serious injury or death.

Содержание ABJET 285
















































Результаты поиска

Содержание ABJET 285

Отзывы:

Похожие инструкции для ABJET 285

Бренды по названию

Популярные бренды

AB Inflatables ABJET 285, Руководство пользователя

Результаты поиска

Содержание ABJET 285

Отзывы:

Похожие инструкции для ABJET 285

Бренды по названию

Популярные бренды