AB Inflatables ABJET 285 Скачать руководство пользователя

Страница: 24 / 47

USE & PERFORMANCE OF YOUR ABJET

TENDER

STARTING THE BOAT / SAFE OPERATION AND MANEUVERABILITY

Starting the boat

WARNING

Avoid personal injury!

Do not allow anyone staying near to the jet pump or intake grate, even

when the engine is off. Items such as long hair, loose clothing or personal

flotation device straps can become entangled in moving parts resulting

in serious injury or drowning. In shallow waters; shells, sand, pebbles, or

other objects could be drawn up by the jet pump.

Turn on battery switch.

Run the bilge blower for 4 minutes.

Ensure shift lever is in neutral position.

Turn on ignition key.

All LED indicators in control panel will turn on for

approximately 3 seconds.

Press the start / stop button until the engine starts.

Indicator lights (pilot lamps) show a selected function, a

normal condition, a system anomaly, or a serious

malfunction. Please check there is no fault condition (See

the Operating the ABJET® Tender Section).

For Emergency cases

Note:

If you must run your boat and your bilge blower is not

working you may ventilate the engine compartment by opening

the console latches and leaving it to air for 4 minutes. It is

important to check your bilge blower and get it repaired in an

authorized service center.

Safe operation and maneuverability

For safety reasons and proper care, perform daily PRE-RIDE

INSPECTION as specified in BRP Operators Manual before

operating your boat.

Please consider the following recommendations:

•

Load the boat within the limits listed on the capacity plate.

Balance loads bow to stern and port to starboard.

•

Maintain boat speed at or below the local legal limit.

Avoid excessive speed.

•

Reduce speed before attempting sudden or sharp turns, and

maintain a proper speed according to water conditions and

environment at all times. Maneuverability at high speed is

limited, and sudden turns may cause loss of boat control.

•

Keep proper lookout and a safe distance all the time to

avoid collisions or accidents.

•

Do not use the boat in adverse weather or waterway

conditions beyond the skill or experience of the operator or

beyond the capability of the boat and comfort of

passengers.

•

In case of emergency, be sure at least one member of the

crew or passengers is familiar with the operation and safety

aspects of the boat.

Содержание ABJET 285
















































Результаты поиска

Содержание ABJET 285

Отзывы:

Похожие инструкции для ABJET 285

Бренды по названию

Популярные бренды

AB Inflatables ABJET 285, Руководство пользователя

Результаты поиска

Содержание ABJET 285

Отзывы:

Похожие инструкции для ABJET 285

Бренды по названию

Популярные бренды