AB Inflatables ABJET 285 Скачать руководство пользователя | Manualshive

Страница: 34 / 47

background image

USE & PERFORMANCE OF YOUR ABJET

®

TENDER

TOWING YOUR INFLATABLE / TRANSPORTING BY ROAD

Davit Lifting

The ABJET®s have three (3) or four (4) davit lifting rings

installed from factory; depending on the davits installed, you

may lift your tender in two different ways: single point or dual

point. Please see diagram.

Davit Lifting

1

Single point davit lifting

2

Dual point davit lifting

NOTICE

Always pump the water from the bilge before lifting the

boat.

CAUTION

Do not hoist the boat with people on board. Lifting attachments

are designed for hosting the boat, engine and standard

equipment

.

WARNING

•

Keep the bow slightly higher than the stern. Remove the drain

plugs when stowing the boat.

•

Never attach lifting cables to grab handles, lifelines, cleats or any

other accessory not intended for lifting purposes. Attach only to the

lifting rings in the transom and bow.

Transporting by road

To transport the ABJET®s, there are several types of trailers

available in the market; however, the trailer must match the

boat’s weight, hull and load. The towing vehicle must have

enough capability for pulling the load. Pulling a load that

exceeds the vehicle’s towing capacity may cause loss of

control.

-

When choosing your trailer, consult your preferred AB

dealer.

-

Always read the trailer owner’s manual carefully before

towing.

-

Check country, state or local regulations and requirements.

-

Disconnect the battery when the boat is being transported.

30

«
...
32
33
34
35
36
...
»

Содержание ABJET 285
















































Отзывы:

Нет отзывов

Похожие инструкции для ABJET 285

Бренд: Zodiac Страницы: 55

Southern Pacific Shearwater 260 AL

Бренд: Kiwi Yachting Страницы: 20

Бренд: TAKACAT Страницы: 3

Бренд: Corsiva Yachting Страницы: 36

Бренд: Tiara Yachts Страницы: 160

Бренд: Mercury Страницы: 4

2008 2008 70141

Бренд: CORRECT CRAFT Страницы: 188

Бренд: Nortik Страницы: 19

Бренд: Nortik Страницы: 21

Бренд: Nortik Страницы: 22

Бренд: Nortik Страницы: 28

Бренд: Nortik Страницы: 33

electric pleasure boat

Бренд: e-motion Страницы: 23

Бренд: Yamaha Страницы: 515

Бренд: MINN KOTA Страницы: 28

Бренд: Jeanneau Страницы: 106

Бренд: Camper & Nicholson Страницы: 22

Бренд: Banzai Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды