Aastra 800 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 136

Aastra 800 Скачать руководство пользователя страница 84

DECT over IP

®

Properties

82

8.

DECT over IP

®

In order to achieve optimal network coverage, a DECT network with several DECT
base stations can be operated. A DECT network is comprised of DECT terminals
connected with the next respective base station (network cell). For users of a DECT
terminal, the handover from DECT base station to base station is completely trans-
parent. Even during a conversation, users are switched from one network cell to
the next without any interruption. Administration of DECT terminals is done cen-
trally via the Aastra 800 Configurator in the

Telephony: Devices: DECT Phones

menu.

Note:

DECT over IP® is a registered trademark of

Aastra DeTeWe GmbH.

8.1

Properties

8.1.1 DECT Base Stations

DECT base stations can be connected to the Aastra 800 via network (TCP/IP).
These DECT base stations are available:

■

RFP 32: Access via shielded CAT5 Ethernet cable (STP cable, Shielded Twisted
Pair cable) with up to 100 metres of cable from the last Ethernet switch, inte-
grated antennas; 8 voice channels

■

RFP 34: like the RFP 32; mounted outside enclosed areas (IP55); external
antennas

■

RFP 42: Access via shielded CAT5 Ethernet cable (STP cable, Shielded Twisted
Pair cable); offers simultaneous function of a WLAN Access Point conforming
with the IEEE 802.11b/g protocol; external antennas; 8 voice channels

Note:

When started, the operating software for the

DECT over IP base stations is transmitted via TFTP protocol
from the Aastra 800. The configuration for the start se-
quence is transmitted by the DHCP server of the Aastra 800
to a DECT over IP base station for the start sequence.

«
...
82
83
84
85
86
...
»

Содержание 800









































































































































Отзывы:

Нет отзывов