Aastra 800 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 136

Aastra 800 Скачать руководство пользователя страница 65

Voice over IP (VoIP)

Fundamentals

63

An IP packet consists of protocol data and user data. Sending shorter voice-data
packets causes the ratio between the user data and the protocol data to become
unfavourable and increases the bandwidth required. Sending longer voice-data
packets increases latency.

The length of the voice-data packets must therefore be adjusted to the require-
ments of the transmission medium. Shorter voice-data packets can be sent if a
direct ethernet connection exists. If an 64 kbit/s ISDN line is to be used for trans-
mission, then longer voice-data packets should be used.

Longer voice data packages are generally used for SIP telephony over the Internet.

The following table provides an overview of the required bandwidth for a tele-
phone connection with various parameter settings. The values apply to half-
duplex ethernet; for full-duplex the values can be halved.

7.2.3 Voice Quality

The achievable voice quality depends on various factors. It is possible to optimise
voice-data transmission on an existing network using the available configuration
settings. Measuring the network quality may also help.

Required bandwidth (kbit/s) with respect to Packet Length and Codec

Packet Length (ms)

G.711 (not compressed) G.729A approx. 8 kbit/s

20

180.8

68.8

30

51.2

40

42.4

50

37.12

60

33.6

70

31.09

80

29.2

«
...
63
64
65
66
67
...
»

Содержание 800









































































































































Отзывы:

Нет отзывов