A.O. Smith PHPT-60 Скачать руководство пользователя страница 40

Страница: 40 / 48

Ambient Temperature Sensor Short or Open or Ad Error (Ambient temperature sensor
circuit is not functioning):

Loose connection or damaged wire-

•

Turn off power at the circuit breaker / fuse box.

•

Check that connector CN212 on control board is seated.

•

Check wires for damage.

Ambient temperature sensor is shorted or open-

•

Unplug ribbon cable from CN212; check resistance between pins 1 and 2 of the ribbon cable

connector. Refer to chart #1 (p.33) for expected resistance value. If the measured resistance is

>40k

or = 0

, the thermisitor is faulty.

•

Replace thermisitor assembly.

Control board faulty-

•

Replace control board.

•

If replacing the control board doesn’t resolve the issue, contact technical support.

Upper Temperature Sensor Short or Open or Ad Error (Upper temperature sensor
circuit is not functioning):

Loose connection or damaged wire-

•

Turn off power at the circuit breaker / fuse box.

•

Check that connector CN204 on control board is seated.

•

Check wires for damage.

Upper temperature sensor is shorted or open-

•

Unplug ribbon cable from CN204; check resistance between pins 1 and 2 of the ribbon cable

connector. Refer to chart #2 (p.33) for expected resistance value. If the measured resistance is

>200k

or = 0

, the thermisitor is faulty.

•

Replace thermisitor assembly.

Control board faulty-

•

Replace control board.

•

If replacing the control board doesn’t resolve the issue, contact technical support.

Lower Temperature Sensor Short or Open or Ad Error (Lower temperature sensor
circuit is not functioning):

Loose connection or damaged wire-

•

Turn off power at the circuit breaker / fuse box

•

Check that connector CN204 on control board is seated.

•

Check wires for damage.

Lower temperature sensor is short or open-

•

Unplug ribbon cable fron CN204; check resistance between pins 3 and 4 of the ribbon cable

connector. Refer to chart #2 (p.33) for expected resistance value. If the measured resistance is

>200k

or =0

, the thermisitor is faulty.

•

Replace thermisitor assembly.

Control board faulty-

•

Replace control board.

•

If replacing the control board doesn’t resolve the issue, contact technical support.

Discharge Temperature Sensor Short or Open or Ad Error (Discharge temperature
sensor circuit is not functioning):

Loose connection or damaged wire-

•

Turn off power at the circuit breaker / fuse box

•

Check that connector CN212 on control board is seated.

•

Check wires for damage.

Discharge temperature sensor is short or open-

•

Unplug ribbon cable from CN212; check resistance between pins 3 and 4 of the ribbon cable

Fault Code Troubleshooting Guide

Содержание PHPT-60
















































Результаты поиска

Содержание PHPT-60

Отзывы:

Похожие инструкции для PHPT-60

Бренды по названию

Популярные бренды

A.O. Smith PHPT-60, Руководство по обслуживанию

Результаты поиска

Содержание PHPT-60

Отзывы:

Похожие инструкции для PHPT-60

Бренды по названию

Популярные бренды