A.O. Smith PHPT-60 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 48

background image

18

CN 211/215 UIM Communication Cable:

•  Pin 1 - +5 V
•  Pin 2 - +12 V
•  Pin 3 - Signal A+
•  Pin 4 - Signal B+
•  Pin 5 - Ground

Note:

Both CN211 and CN215 are identical and either can be used for the UIM communication.

CN 208 Overload Detection:

•  Pin 1 - High pressure switch.
•  Pin 2 - High pressure switch.
•  Pin 3 - Low pressure switch.
•  Pin 4 - Low pressure switch.
•  Pin 5 - Not used
•  Pin 6 - Not used
•  Pin 7 - Not used
•  Pin 8 - Not used
•  Pin 9 - Condensate pump signal over

fl

ow (optional)

• Pin 10 - Condensate pump signal over

fl

ow (optional)

Note:

Pin 9 and 10 are connected by a jumper wire. This wire should be cut and wired in series to

the over

fl

ow switch of the

fi

eld supplied condensation pump (optional).

SW 201 Dip Switch:

•  SW 1 - Not used
•  SW 2 - Not used
•  SW 3 - Not used
•  SW 4 - Not used

Led 201 Power Indicator:

• LED 201 when illuminated, indicate that 5 and 12 Volts DC are present for the UIM

Section D

LED 202/203 Powered Anode Indicators:

• LED

202-

One (1)

fl

ash/second (approx.), indicates

there is power to the anode circuit.

• LED

203-

Two (2)

fl

ashes/second (approx.), indicates

proper operation.
Four (4)

fl

ashes/second (approx.),

indicates a fault.

Figure 9

LED
203 / 202

Section D

Section “C” of Control Board (con’t)

«
...
16
17
18
19
20
...
»

Содержание PHPT-60

















































Отзывы:

Нет отзывов

Похожие инструкции для PHPT-60

Бренд: L.B. White Страницы: 80

Бренд: hajdu Страницы: 136

Бренд: DAYGAS Страницы: 32

GreenSpec HTHB-HVRGRN

Бренд: Halsey Taylor Страницы: 7

Бренд: Sentiotec Страницы: 72

Nano-Flow 2,600

Бренд: Cobalt Digital Inc Страницы: 2

Бренд: esotec Страницы: 2

Dead Level Series

Бренд: Watts Страницы: 24

Бренд: Harvia Страницы: 15

Бренд: Whale Страницы: 60

Бренд: H2O International Страницы: 20

(C)(GC)IR6PMA series

Бренд: IHP Страницы: 28

Бренд: BN Thermic Страницы: 4

Бренд: Drazice Страницы: 28

Бренд: samhydraulik Страницы: 9

Бренд: Trigano PISCINES Страницы: 13

Бренд: Far Group Страницы: 12

Бренд: GE Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды